10 - 20 days
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
UNI-T UT171C Multimeter
The UT171 series multimeters are portable multimeters with automatic and manual range switching and a resolution of 4 3/4 to 4 5/6 digits. These devices belong to the upper mid-range class, excel in quality design and reliability, and are also suitable for industrial use. They can measure AC/DC voltage and current, resistance, diode test, continuity test, capacitance, frequency, duty cycle, temperature, 4-20mA current loop, conductivity, VFC, and NCV. The devices allow data storage and connection via USB with optical isolation or via Bluetooth.
The UNI-T UT171C multimeter is the best instrument in the UT171 series.
Unlike the UT171A, the UT171C has a wider range for resistance and capacitance measurement, as well as (reverse) resistance measurement. The display type is OLED with a dot matrix. The display range is ±60,000 for voltages, currents and frequencies, and ±6,000 for capacitance measurements. The display includes a 31-segment analogue bar graph. The refresh rate is 4 to 5 times per second. The fuses are protected by tubular fuses (10A FF 10A H / 1000V fuse (10 x 38mm); mA / µA FF 800mA H / 600V fuse (6 x 32mm)). The device can test its own fuses (without opening the device). The multimeter is powered by a 7.4 V / 1800 mAh lithium battery. The measurement range can be selected automatically or manually. Test leads with tips in safety categories CAT III 1000V and CAT IV 600V are included.
Product specifications:
- fully compliant with IEC/EN61010-1 and feature double insulation
- classified as CAT III 1000V - electrical installation including three-phase distribution
- classified as CAT IV 600V - outdoor electrical installation (fuse boxes, start of indoor installation)
- Maximum display is 60,000, an inverted OLED dot-matrix display
- 60,000-count frequency measurement display
- 6000 capacitance measurement display
- Refresh rate for most measurements: 4 to 5 times per second
- Manual measurement range
-/> Ranges: 600 mV / 1000 V
- AC current measurement ranges: 600 μA / 10 A
- DC voltage measurement ranges: 600 mV / 1000 V
- DC current measurement ranges: 600 μA / 10 A
- Current measurement ranges
-600/10 A
Clamp A
- Resistance measurement ranges: 600 Ω / 60 MΩ
- Capacitance measurement ranges: 60.00 nF / 60.00 mF
- Measurement ranges: 60 Hz to 10 MHz
- Square-wave signal generator duty cycle from 0.80 Hz to 0.80 Hz
: 1.0% to 99%
- Duty cycle measurement range: 100.0 ms to 0.100 µs
- Conductivity measurement range: 60 nS
- Temperature measurement range: -40 °C to 1000 °C (supplied only with a K-type thermocouple + nickel-chromium-silicon + nickel 230°C)
- High accuracy
- Analogue bar graph scale, 31 divisions
- TRMS, measurement of rms voltage, AC voltage and currents
- During AC voltage measurement, the frequency or duty cycle of the voltage can be measured on the secondary display
- On the secondary display, it is also possible to measure the AC component superimposed on DC voltage
- Data logging of 1000 values
- Relative measurement mode
- measurement of MAX and 1 MIN peak response
Faulty wiring
- Low battery indicator
- Auto-off (sleep mode when inactive)
- Overload protection for voltage inputs
- Overvoltage protection on inputs with fast-acting fuses
- 10MΩ input impedance
- Non-contact voltage detection without test probes
- Semiconductor transition to diodes and 3V voltage test semiconductors
- Powered by a 7.4V / 1,800mAh Li-ion battery
- USB cable supplied with converter; software can be downloaded from the manufacturer’s website: https://meters.uni-trend.com/product/ut171-series/#Docs
- Option to purchase a Bluetooth adapter
DC-D08V/UT-D08V supplied with 500mA power supply and accessories
- Measurement in electromagnetic fields with an intensity of 1V/m is also possible, with an additional error of 5%
Technical parameters:
(accuracy is defined at 23°C ± 5°C and relative humidity less than or equal to 75%)
- DC voltage measurement (input impedance) resolution is:
600.00 mV / 10 µV / ± 0.025% + 5
6.0000 V / 0.1 mV / ± 0.025 % + 5
60.000 V / 1 mV / ± 0.025 % + 5 / ± 0.0 mV / ± 0.0 mV 0.03 % + 5
1000.0 V / 100 mV / ± 0.03 % + 5
- AC voltage measurement (input impedance is 10 MΩ, 45 Hz to 1 kHz):
(range / resolution / accuracy)
0.03 % + 5 mV ± 0.4 % + 40
6.0000 V / 0.1 mV / ± 0.025 % + 5
60,000 V / 1 mV / ± 0.025 % + 5
600.00 V / 10 mV / 10 mV / ± 0.000 V / 1 mV / ± 0.000 V / 1 mV / ± 0.000 V / 10 mV / ± 0. 100 mV / ± 0.03% + 5
LoZ 100.0 V / 0.1 V / ± 2.0 % + 10
V.F.C. 600V/1000V / 0.01 V/0.1 V / ± 2.0 % + 10
- DC measurement:
(range / resolution / accuracy)
600.0 μA / 0.01 μA / ± 0.20 μA / ± 0.20 μA / ± 0.20 %/0 μA 0.1 μA / ± 0.25 % + 2
60,000 mA / 1 μA / ± 0.7 % + 2
600.0 mA / 10 μA / ± 0.15% + 2
6,000 A / 0.1 mA / ± 0.1 mA / 1 mA / ± 0.5 % + 2
% (4–20 mA) / 0.01 % / ± 0.5 % + 2
- AC current measurement (45 Hz to 1 kHz):
(range / resolution / accuracy)
- AC current measurement (45 Hz to 1 kHz):
(range / resolution / accuracy)
0. 0.75% + 20
6000.0 μA / 0.1 μA / ± 0.75% + 20
60,000 mA / 1 µA / ± 0.75% + 20
600.000 mA / ± 2.0 µA / ± 2.0 %
6.0000 A / 0.1 mA / ± 1.5 % + 20
10,000 A / 1 mA / ± 1.5 % + 5
- DC current measurement using the current clamp:
60 A range (at 10 mV / ± 0.01 accuracy) + 30)
600A range (at 1mV/A) / resolution 0.01A / accuracy ±(1.0% + 30)
- AC current measurement using the current clamp:
60A range (at 10mV/A) / resolution 0.001%/(0.001%
/ accuracy) range 600A (at 1mV/A) / resolution 0.01A / accuracy ±(1.2% + 30)
- Resistance and conductivity measurement:
(range / resolution / accuracy)
600.00 Ω / 0.01 Ω / 0.01 Ω / ± 0.0 Ω / ± 0.0 Ω / ± 0.0 Ω / ± 0.0 Ω kΩ / 0.1 Ω / ± 0.05 % + 2
60,000 kΩ / 1 Ω / ± 0.05 % + 2
600.00 kΩ / 10 Ω / ± 0.05 % + 2
6,000 MΩ / ± 0.000 Ω / ± 0.05 % + 2
60,000 MΩ / 1 kΩ / ± 3 % + 2
60.00 nS / 0.01 nS / ± 1 % + 10 (S = Siemens unit)
- Capacitance measurement:
(range / resolution / accuracy)
3 p.
60.00 nF to 600.0 µF / 10 pF to 100 nF / ± 2.5 % + 5
6.000 mF to 60.00 mF / 1 µF to 10 µF / ± 10 % measurement period: cycle and frequency
Measurement range: (range / resolution / accuracy)
60,000 Hz to 10,000 MHz / 0.0001 Hz to 0.001 MHz / ± 0.01% + 5
0.1% to 99.9% / 0.1% / ± 3.0% / ¼ to 410
- Square wave generator:
Frequency 0.5 Hz to 4800 Hz / 0.1 Hz step size / accuracy 0.1 % / ± ¼ to 5 %. 100% / 0.1% step size / accuracy ± 0.5 %
Amplitude / 0.8 Vp / accuracy ± 0.2 Vp
- Inverted display type, dot-matrix OLED
- Sampling frequency: 4 to 5 / 0 sec. Analogue display: 31 segments
- Power supply: 7.4V / 1800mAh Li-ion battery
- 10A fuse protection with FF 10A H / 1000V fuse (10 x 38mm)
- mA / µA fuse protection: FF 800mA / 610mA/H 30/mm fuse; instrument dimensions: 206 x 95 x 53 mm
- Weight: approx. 500 g (including batteries)
- operating temperature: 0°C to 40°C
- relative operating humidity at 0°C to 30°C less than or equal to 75%, at 30°C to 40°C less than or equal to 50%
- Storage temperature: -5/10°C; up to -10°C for current clamps, for ranges up to 600A
- The device complies with the following standards:
cETLus, CAT III 1000V, CAT IV 600V, double insulation, overvoltage protection greater than 1000V
EN 61326-1: 201; EN 61326-2-2: 2013
EN 61010-1: 2010; EN 61010-2-030: 2010; EN 61010-2-033: 2012
Compliant with UL STD.: 61010-1, 61010-2-030
Certified to CSA STD. C22.2 No. 61010-1, 61010-2-030, 61010-2-033
- Manufacturer: UNI-TREND
-
Package contents:
- UT171C multimeter with Li-I storage case
-7 with 4V, 1800mAh battery - built-in
- Fuse F1: FF 800mA H 1000V (6 x 32mm) - in device
- Fuse F2: FF 10A H 1000V (10 x 38mm) - in device
- USB cable with opto-electronic converter
- Type K thermocouple (nickel-chromium-nickel-silicon) up to +230 °C
- Test leads with CAT III 1000V, CAT IV 600V tips
- DC 10V / 500mA power supply with accessories
- User manual in Czech, Slovak and English
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
UNI-T UT123T Multimeter
This product comes with a 3-year warranty. The UNI-T UT123T is a simple, portable multimeter for domestic use. Its compact design makes it easy to hold in one hand, and the EBTN display allows users to read values clearly from any angle. Intelligent non-contact AC electric field detection, which distinguishes between weak, strong and super-strong electric fields.
Product specifications:
- Measurement of AC/DC voltage, resistance, temperature, indication of broken wires
- Indication of the electromagnetic field around live AC wires
- Automatic battery status check
- Automatic identification of AC V/DC V measurements
- Automatic measurement of the break interval and voltage interruption for
- 15 minutes of inactivity
- Maximum display value: 4099
Technical parameters:
DC voltage measurement: 4V / 40V / 400V / 600V ± (0.5% + 2)
AC voltage: 4V / 4V / 4V / 400V / 600V ± (1.0% + 3)
Resistance measurement: 400Ω / 4kΩ / 40kΩ / 400kΩ / 4MΩ / 20MΩ ± (0.8% + 2)
Temperature measurement: from -40 °C to +300 °C to -570 °F / -570 °F (non-contact voltage detection)
Open circuit indication
Display type: EBTN
Display size: 44 x 26 mm
Maximum display value: 4099
Sampling frequency: 3 times per second
Power supply: 2xAAA batteries
Measurement 5AAA
600V standard
Dimensions: 130 x 65 x 28mm
Weight: 130g
Package contents:
- 1 pair of test leads
- 1 thermocouple
- 1.5V AAA batteries: 2
6 pcs.
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
UNI-T UT116A Multimeter
This product comes with a 3-year warranty. The UT116A tester is a device for testing SMD soldered electronic components. The four-digit display with a range of 3000 can display voltage up to 36V, resistance up to 30MΩ, and capacitance up to 30mF. It is also possible to test diodes and Zener diodes, as well as circuit continuity with a low resistance indication of less than 30Ω.
Product specifications:
- voltage measurement up to 36 V DC
- automatic identification of resistance, capacitance and diodes
- circuit resistance measurement,
- continuity,
capacitance,
capacitance> the pen can be rotated 180° from the tips, which is convenient for reading data from the display when measuring diodes/LEDs
- Zener diode polarity test
- low battery indicator
- automatic switch-off after 10 minutes of inactivity
Technical parameters:
-0 Automatic switching range:
-0 Voltage measurement up to: 36 V DC
- Resistance measurement: 30 MΩ
- circuit continuity test: ＜ 30Ω
- Capacitance measurement up to: 30 mF
- diode test: 3V
- LED test: stabilised voltage approx. 21 V / 1 mA
- Power supply: 1.5 V (AAA) batteries x 2
- display dimensions: 39 mm x 20 mm
- External dimensions: 204 mm x 33 mm x 25 mm
- Product weight: approx. 80 g
- Product colour: red and grey/
Individual packaging contents
:
- UT116A tester: 1 pc
- 1.5V (AAA) battery: 2 pcs
- manual in Czech and English
- a gift box
Packaging for wholesale customers:
- Standard quantity per box: 600 pcs x box: 400 pcs x 4 mm x 210 mm
- gross weight of the carton: approx. 7.1 kg
MANUFACTURER: UNI-TREND
https://www.uni-trend.com/
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
UNI-T UT116C Multimeter
This product comes with a 3-year warranty. The UT116C tester is a device for testing SMD soldered electronic components. On a 4-digit display with a range of 6000, it is possible to display resistance up to 60MΩ and capacitance up to 100mF. It is also possible to test diodes and Zener diodes, as well as circuit continuity with an indication for resistance below 50Ω.
Product parameters:
- measurement of resistance, circuit continuity, capacitance, diodes
- the pen can be rotated 180°, which is convenient for reading data from the tips, from which the display is convenient for measurement. LEDs
- Zener diode polarity test
- Low battery test
- Automatic shut-off after 15 minutes of inactivity
Technical parameters:
- Display range: 6000
- Automatic range switching
- Resistance measurement: 60MΩ Circuit continuity test
- up to: 100 mF
- Diode test: 3.2 V
- LED test: stabilised voltage approx. 21 V / 1 mA
- Battery test at a load current of 10 mA
- Power supply: 1.5 V (AAA) batteries x 2
- display dimensions: 39 mm x 20 mm
- External dimensions: 204 mm x 33 mm x 25 mm
- Product weight: approx. 8 g
- grey
Contents of individual pack:
- UT116C tester: 1 pc
- 1.5V (AAA) battery: 2 pcs
- Manual in Czech and English
- a gift box
Packaging for wholesale customers:
0 pcs
- 6 pcs. Standard box dimensions: 440 mm x 420 mm x 210 mm
- Gross weight of the box: approx. 7.1 kg
MANUFACTURER: UNI-TREND
https://www.uni-trend.com/
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
UNI-T UT161B Multimeter
This product comes with a 3-year warranty. The UT161 series of multimeters is a range of extremely reliable, safe, durable and accurate multimeters that are CE-certified and suitable for the European market. The displays on these multimeters are backlit LCDs (dark digits on a light background) with a resolution of ±6000 (for the UT161B and UT161D) and ±22000 for the UT161E. The displays have a refresh rate of 2–3 times per second and also feature an analogue bar graph with 31 segments (UT161B and UT161D) or 41 segments (UT161E). The multimeters measure AC and DC voltages up to 1000V and are equipped with an audible and visual warning when maximum voltage/current or temperature values are reached. They allow for non-contact detection of live AC wires. The package includes a USB cable with an opto-electronic converter for data transfer to a PC. The power supply consists of four AAA (R03) batteries, and the device switches off automatically after 15 minutes of inactivity (this function can be temporarily disabled). The current inputs are protected by tubular fuses, and the fuses can be tested without opening the device.
UT161B True RMS 1000 V digital multimeter.
Product specifications:
- fully complies with IEC/EN61010-1, and features double insulation classified as CAT/III
1000V – indoor electrical installation including three-phase distribution
- Classified as CAT IV 600V – outdoor electrical installations (fuse boxes, start of indoor installations)
- HTN-type LCD display with a maximum reading of ± 6000
- refresh rate for most measurements of 3 times per second
- Automatic or manual setting ranges
- automatic polarity indication
- AC voltage measurement ranges: 60>-0V AC
Ranges: 600 μA / 10 A
- DC voltage measurement ranges: 60 mV / 1000 V
- DC current measurement ranges: 600 μA / 10 A
- Resistance measurement ranges: 600 MΩ Capacitance: 600 MΩ / 60 MΩ–60 MΩ nF / 66 mF
- Frequency measurement range: 10 Hz / 10.00 MHz
- Duty cycle measurement range: 0.1% to 99.9%
- Measurement of silicon diode transitions
- Line continuity measurement
- Non-contact high-voltage measurement
TRV detection – accuracy
NC
RMS voltage values, voltages and currents
- relative measurement mode
- MAX / MIN mode
- Overrange warning: OL
- USB cable for transferring measured values to a PC
- Input protection against overvoltage exceeding 1000V
- μA and mA input current protection with m0 V 6100 ø 6100 V 32mm CE fast-acting fuse
- Input current protection 10A via FF11A / 1000V fast-acting fuse ø10 x 38mm CE
- Input impedance in the mV range approx. 1GΩ, in other voltage ranges 10MΩ,
- testing of diodes and semiconductor junctions with voltage from 0 to 3V, test current 1.2mA
- powered by 4 x 1.5V AAA R03 batteries
- low battery indicator
- automatic switch-off after 15 minutes of Bluetooth data transfer
- optional adapter for PC
to PC
- measurement possible in electromagnetic fields with an intensity of 1 V/m with an additional error of 5%
Technical parameters:
(accuracy is defined at a temperature of 23 °C ± 5 °C and relative humidity less than or equal to 75%)
- DC voltage measurement (input range is approximately 1MV, 1MΩ 0x0x.) for other ranges):
(range / resolution / accuracy)
60.00 mV / 0.01 mV / ± (0.8% + 5)
600.0 mV / 0.1 mV / ± (0.8 % + 3)
6,000 V / 5 / 0.01 V / ± 0.1 mV / ± (0.8 % + 3) 60.00 V / 0.01 V / ± (0.5 % + 3)
600.0 V / 0.1 V / ± (0.5 % + 3)
1,000 V / 1 V / ± (1.0 % + 3)
- (in AC input voltage measurement / Ω) range / resolution / accuracy in the range from 40 Hz to 500 Hz)
60.00 mV / 0.01 mV / ± (1.2 % + 5)
600.0 mV / 0.1 mV / ± (1.2 % + 5)
6.00 ± 0 V / 0.0 ± 0 V / ± 0 V
60.00 V / 0.01 V / ± (1.0 % + 3)
600.0 V / 0.1 V / ± (1.0 % + 3)
1000 V / 1 V / ± (1.2 % + 5)
Displays the actual current value/
(range / resolution / accuracy)
600.0 μA / 0.1 μA / ± (1.0 % + 2)
6000 μA / 1 μA / ± (1.0 % + 2)
60.00 mA / 10 μA / ± 0.0 μA / ± 0.0 μA / ± (1.0 % + 2) mA / 0.1 mA / ± (1.0 % + 3)
6,000 A / 1 mA / ± (1.2 % + 5)
10,000 A / 10 mA / ± (1.2 % + 5)
- AC current measurement resolution in the range H / z / z / accuracy: 500 Hz)
600.0 μA / 0.1 μA / ± (1.2 % + 5)
6000 μA / 1 μA / ± (1.2% + 5)
60.00 mA / 10 μA / 10 μA / ± 5.0 %, ± (1.0 % + 5)
mA / ± (1.5 % + 5)
6,000 A / 1 mA / ± (2.0 % + 5)
10 A / 10 mA / ± (2.0 % + 5)
Displays the true RMS value
-
- Resistance measurement range: /> resolution accuracy 600.0 Ω / 0.1 Ω / ± (1.2 % + 2)
6,000 kΩ / 1 Ω / ± (1.0 % + 2)
60.00 kΩ / 10 Ω / ± (1.0 % + 2)
600.0 % + 2 Ω / 600.0 % + 2)
600.00 kΩ / 10 Ω / ± (1.0 % + 2)
600.0 % + 2)
6,000 MΩ / 1 kΩ / ± (1.2 % + 2)
60.00 MΩ / 10 kΩ / ± (2.0 % + 5)
- Capacitance measurement:
(range / resolution / accuracy)
nF / 3.0 % / ± 0.0 % 5)
600.0 nF / 100 pF / ± (3.0 % + 5)
6,000 μF / 1 nF / ± (3.0% + 5)
60.00 μF / 10 nF / ± (3.0% + 5) / ± (3.0% + 5) (3.0% + 5)
6,000 mF / 1 μF / ± (10 % + 5)
60.00 mF / 10 μF / ± (10 % + 5)
- Frequency measurement:
(range / resolution / accuracy 10 MHz) 10 MHz 0.01 Hz to 0.01 MHz / ± 0.1% + 4
- Duty cycle measurement:
0.1% to 99.9% / 0.1% / ± (2.0% + 5)
- Measurement of semiconductor and semiconductor measurement value 0.12 to 2 V and the green LED is lit: the diode is OK,
the measured value is less than 0.12 V and the red LED is lit: the diode may be damaged
the normal voltage drop across the silicon junction is 0.500 to 0.800 mV
voltage resolution during this measurement. continuity measurement:
when the line resistance is ≥70 Ω, an open circuit is indicated, the buzzer does not beep and the red indicator light is on
when the line resistance is ≤50 Ω, a continuous circuit is indicated, the buzzer emits a continuous beep and the green indicator light is on
This resolution for overload protection
10:00V: 0.1 Ω
General specifications:
- operating temperature: 0 °C - 40 °C (32 °F - 104 °F)
- Relative humidity: ≤75% at 0 °C – 30 °C; ≤50% at 30 °C – 40 °C
- Storage temperature: -10°C – 50°C (14°F – 122°F)
- Operating altitude: ≤2000 m
- Electromagnetic compatibility: complies with EN61326-1: 2006
- dimensions: 186 mm × 89 mm × 49 mm
- Weight: 400 g
- the device complies with the following standards:
cETLus, CAT III 1000V, CAT IV 600V, double insulation, overvoltage protection for voltages greater than 102>1000V
1000V; EN 61326-2-2: 2013
EN 61010-1: 2010; EN 61010-2-030: 2010; EN 61010-2-033: 2012
Compliant with UL STD: 61010-1, 61010-2-030
Certified to CSA STD. C22.2 No. 61010-1, 61010-2-030, 61010-2-033
Package contents:
- UT161B multimeter with storage case
- Gold-plated measurement leads CAT600/1 CAT III/1000 CATV-III USB cable for data transfer to PC
- F1 fuse: 6 x 32 mm FF 600mA H 1000 V (ø6 x 32mm) CE - in the device
- Fuse F2: 6 x 25 mm FF 11A H 1000 V (ø10 x 38 mm) CE -- in the R40 AAA device
-- 1.5 V batteries
- manual in Czech, Slovak, English
Wholesale packaging:
- standard quantity per box: 20 pcs
- standard box dimensions: 480 mm x 370 mm x 325 mm
- total box weight: 17.8 kg
- Manufacturer
- UNI-TREND
-
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
UNI-T UT161D Multimeter
This product comes with a 3-year warranty. The UT161 series of multimeters is a range of extremely reliable, safe, durable and accurate multimeters that are CE-certified and suitable for the European market. The displays on these multimeters are backlit LCDs (dark digits on a light background) with a resolution of ±6000 (for the UT161B and UT161D) and ±22000 for the UT161E. The displays have a refresh rate of 2–3 times per second and also feature an analogue bar graph with 31 segments (UT161B and UT161D) or 41 segments (UT161E). The multimeters measure AC and DC voltages up to 1000V and are equipped with an audible and visual warning when maximum voltage/current or temperature values are reached. They allow for non-contact detection of live AC wires. The package includes a USB cable with an opto-electronic converter for data transfer to a PC. The power supply consists of four AAA (R03) batteries, and the device switches off automatically after 15 minutes of inactivity (this function can be temporarily disabled). The current inputs are protected by tubular fuses, which can be tested with this device without opening them.
UT161D True RMS 1000 V Digital Multimeter.
Product specifications:
- Fully complies with IEC/EN61010-1 and features double internal insulation
- included in the CAT IV 600V category – outdoor electrical installation (fuse elements, start of internal installation)
- HTN-type LCD display with a maximum reading of ± 6000
- refresh rate for most measurements of 3 times per second
- Automatic or manual setting ranges
- Automatic polarity indication
- AC voltage measurement ranges: 60>-0V AC
Ranges: 600 μA / 20 A
- DC voltage measurement ranges: 60 mV / 1000 V
- DC current measurement ranges: 600 μA / 20 A
- LoZ V~ function – low input impedance measurement (approx. resistance: 600 Ω / 60 MΩ
- Capacitance measurement range: 60 nF / 66 mF
- Measurement frequency range: 10 Hz / 10.00 MHz
- Duty cycle measurement range: 0.1% to 99.9%
- 4000 °C to 4000 °C (1832 °F to 1832 °F), with supplied thermocouple up to 230 °C (446 °F)
- Measurement of silicon diode transitions
- Line continuity measurement
- Non-contact voltage detection (NCV)
- high accuracy
- TRMS, measurement of true RMS values of voltage, current and power
- Relative measurement mode
- MAX/MIN mode
- Overload warning: OL
- USB cable for transferring measured values to a PC
- Input protection against overvoltage exceeding 1000V
- μA and mA input current protection with m0 V 6100 ø 6100 V 32mm CE fast-acting fuse
- Input current protection 10A via FF11A / 1000V fast-acting fuse ø10 x 38mm CE
- Input impedance in the mV range approx. 1GΩ, in other voltage ranges 10MΩ,
- testing of diodes and semiconductor junctions with voltage from 0 to 3V, test current 1.2mA
- powered by 4 x 1.5V AAA R03 batteries
- low battery indicator
- automatic switch-off after 15 minutes of Bluetooth data transfer
- optional adapter for PC
to PC
- measurement possible in electromagnetic fields with an intensity of 1 V/m with an additional error of 5%
Technical parameters:
(accuracy is defined at a temperature of 23 °C ± 5 °C and relative humidity less than or equal to 75%)
- DC voltage measurement (input range is approximately 1MV, 1MΩ 0x0x.) for other ranges):
(range / resolution / accuracy)
60.00 mV / 0.01 mV / ± (0.8% + 5)
600.0 mV / 0.1 mV / ± (0.8 % + 3)
6,000 V / 5 / 0.01 V / ± 0.1 mV / ± (0.8 % + 3) 60.00 V / 0.01 V / ± (0.5 % + 3)
600.0 V / 0.1 V / ± (0.5 % + 3)
1,000 V / 1 V / ± (1.0 % + 3)
- (in AC input voltage measurement / Ω) range / resolution / accuracy in the range from 40 Hz to 1 kHz)
60.00 mV / 0.01 mV / ± (1.2 % + 5)
600.0 mV / 0.1 mV / ± (1.2 % + 5)
6.00 % + 3 V / 0.00 V / ± 0 V
60.00 V / 0.01 V / ± (1.0 % + 3)
600.0 V / 0.1 V / ± (1.0 % + 3)
1000 V / 1 V / ± (1.2 % + 5)
LoZ ACV / ± 0.0 % V / ± 0.0 V / ± 0.0 V / ± (1.2 % + 3) 5)
LoZ ACV 1000 V / 1 V / ± (2.0 % + 5)
Displays the true RMS value.
- DC measurement:
(range / resolution / accuracy)
600.0 μA / 0.1 μA / ± 1 μA,
μA / 1 μA / ± (1.0 % + 2)
60.00 mA / 10 μA / ± (1.0 % + 3)
600.0 mA / 0.1 mA / ± (1.0 % + 3)
6,000 A / ± 1.2 mA / ± 1.0 mA / ± A / 10 mA / ± (1.2 % + 5)
- AC current measurement:
(range / resolution / accuracy in the range from 40 Hz to 1 kHz)
600.0 μA / 0.1 μA / ± (1.2 % + μA / μA / ± 50 / μA / ± 1 kHz) (1.2 % + 5)
60.00 mA / 10 μA / ± (1.5 % + 5)
600.0 mA / 0.1 mA / ± (1.5 % + 5)
6,000 A / 1 mA / ± (2.0 % / ± 5 mA / ± 5)
(2.0% + 5)
Displays the true RMS value
- Resistance measurement:
(range / resolution / accuracy)
600.0 Ω / 0.1 Ω / ± (1.2 % + 2)
6,000 kΩ / ± 1.0 Ω / ± 1.0 Ω / ± 1.0 Ω / ± 1.0 Ω 60.00 kΩ / 10 Ω / ± (1.0 % + 2)
600.0 kΩ / 100 Ω / ± (1.0 % + 2)
6,000 MΩ / 1 kΩ / ± (1.2% + 2)
60.00 kΩ / ± 2 Ω / ± 2 Ω / 60.00 % + 2)
- Capacitance measurement:
(range / resolution / accuracy)
60.00 nF / 10 pF / ± (3.0 % + 5)
600.0 nF / 100 pF / ± (3.0 % + 5) / ± 6.0 pF / ± 10 pF / ± (3.0 % + 5) % + 5)
60.00 μF / 10 nF / ± (3.0% + 5)
600.0 μF / 100 nF / ± (3.0% + 5)
6,000 mF / 1 μF / ± (10 % + 5 μF / 0.0 % + 5) / μF / 0.0 % + 5) ± (10 % + 5)
- Frequency measurement:
(range / resolution / accuracy)
10 Hz to 10 MHz / 0.01 Hz to 0.01 MHz / ± 0.1% + 4
- Duty cycle measurement / 9.1 %/ to 9.1 % 0.1 % / ± (2.0 % + 5)
- Temperature measurement in the range -40 °C to 1000 °C (-40 °F to 1832 °F):
(range / resolution / accuracy)
-40 °C / ± 0 °C / ± 1% °C)
0 °C to 300 °C / 1 °C / ± (1.0% + 2 °C)
300 °C to 1000 °C / 1 °C / ± (1.0% + 3 °C)
(range / resolution / accuracy)
(range / resolution / accuracy)
± 3 °F / ± 3 °F (1.0% + 6 °F)
32 °F to 572 °F / ± (1.0% + 4 °F)
572 °F to 1832 °F / 2 °F / ± (1.0% + 6 °F)
With a type K thermocouple, the temperature should be measured at less than 20 °C (446 °F)
Conversion from °C to °F using the formula °F = 1.8 × °C + 32
- Measurement of diodes and semiconductor junctions:
if the measured value is between 0.12 and 2 V and the green LED is lit, the measured value is lower than 0.12 V and the red LED is lit: the diode may be damaged
the normal voltage drop across the silicon junction is 0.500 to 0.800 mV
Voltage resolution during this measurement: 0.001 V
- Circuit continuity measurement:
when the line is open, the resistance is ≥70 ohms, the buzzer does not beep and the red indicator light is on
when the line resistance is ≤50 Ω, an unbroken circuit is indicated, the buzzer emits a continuous beep and the green indicator light is on
Overload protection: 1000V
Resistance resolution for this measurement: 0.1 Ω
General operating specifications:
0°C – 40°C (32°F – 104°F)
- relative humidity: ≤75% at 0°C - 30°C; ≤ 50% at 30°C - 40°C
- Storage temperature: -10°C - 50°C (14°F - 122°F)
- Operating altitude: ≤2000 m
- Electromagnetic compatibility: complies with EN61326-1: 2006
- dimensions: 186 mm × 89 mm × 49 mm
- Weight: 400 g
- the device complies with the following standards:
cETLus, CAT III 1000V, CAT IV 600V, double insulation, overvoltage protection for voltages greater than 102>1000V
1000V; EN 61326-2-2: 2013
EN 61010-1: 2010; EN 61010-2-030: 2010; EN 61010-2-033: 2012
Compliant with UL STD: 61010-1, 61010-2-030
Certified to CSA STD. C22.2 No. 61010-1, 61010-2-030, 61010-2-033
Package contents:
- UT161D multimeter with storage case
- Gold-plated CAT III test leads / CAT IV 60V / 100/100V adapter plug - CAT IV 60V plug – for thermocouple connection
- Type K thermocouple
- USB cable for data transfer to PC
- Fuse F1: 6 x 32 mm FF 600mA H 1000 V (ø6 x 32mm) CE - in device
- Fuse F2: 6 x 25 mm FF 1001A in V8 mm (ø) x CE device
- 4 AAA batteries, R03 1.5 V
- manual in Czech, Slovak and English
Wholesale packaging:
- standard quantity per box: 20 pcs
- standard box dimensions: 480 mm x 370 mm x 325 mm total box weight
- 1 kg
- Manufacturer: UNI-TREND
-
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
UNI-T UT161E Multimeter
This product comes with a 3-year warranty. The UT161 series of multimeters is a range of extremely reliable, safe, durable and accurate multimeters that are CE-certified and suitable for the European market. The displays on these multimeters are backlit LCDs (dark digits on a light background) with a resolution of ±6000 (for the UT161B and UT161D) and ±22000 for the UT161E. The displays have a refresh rate of 2–3 times per second and also feature an analogue bar graph with 31 segments (UT161B and UT161D) or 41 segments (UT161E). The multimeters measure AC and DC voltages up to 1000V and are equipped with an audible and visual warning when maximum voltage/current or temperature values are reached. They allow for non-contact detection of live AC wires. The package includes a USB cable with an opto-electronic converter for data transfer to a PC. The power supply consists of four AAA (R03) batteries, and the device switches off automatically after 15 minutes of inactivity (this function can be temporarily disabled). The current inputs are protected by tubular fuses, and the fuses can be tested without opening the device.
UT161E 1000 V True RMS Digital Multimeter.
Product specifications:
- fully complies with IEC/EN61010-1 and features CAT-III-0 double insulation
V-10 indoor electrical installation including three-phase distribution
- Classified as CAT IV 600V - outdoor electrical installation (safety components, start of indoor installation)
- HTN-type LCD display with a maximum reading of ± 22,000
- refresh rate for most measurements of 3 times per second
- Automatic or manual setting ranges
- Automatic polarity indication
- AC voltage measurement ranges: V / 21000 mV / 21/2000 mV Ranges: 220 μA / 20 A
- DC voltage measurement ranges: 220 mV / 1000 V
- DC current measurement ranges: 220 μA / 20 A
- Resistance measurement ranges: 220 mV / 200 V
- Capacitance measurement ranges: 220 Ω / 20 A / 220 mF
- Frequency measurement range: 10 Hz / 220 MHz
- Measurement of transistor gain (β)
- Measurement of silicon diode transitions
- Line continuity measurement
- Non-contact voltage detection (NCV)
- High accuracy of TRMS effective voltage measurement, voltage and current
- Relative measurement mode
- MAX/MIN mode
- Over-range warning: OL
- VFC anti-interference filter
- USB cable for transferring measured values to a PC
- software can be downloaded from the manufacturer’s website: https://meters.uni-series/161/products/series/#61 input protection against overvoltage exceeding 1000V
- Input current protection (μA and mA) with FF600 mA H 1000 V fast-acting fuse, ø6 x 32 mm CE
- Input current protection via FF11A / 1000V fast-acting fuse, ø10 x 38mm CE
- 1GΩ, 10MΩ in other voltage ranges,
- testing of diodes and semiconductor junctions with voltage from 0 to 3V, test current 1.2mA
- powered by 4 x 1.5V AAA R03 batteries
- low battery indicator
- automatic shut-off after 15 minutes of Bluetooth data transfer
- optional adapter for PC
to PC
- measurement possible in electromagnetic fields with an intensity of 1 V/m with an additional error of 5%
Technical parameters:
(accuracy is defined at a temperature of 23°C ± 5°C and relative humidity less than or equal to 75%)
- DC voltage measurement (input range is approx. 1 mV/Ω for other ranges):
(range / resolution / accuracy)
220.00 mV / 0.01 mV / ± (0.1% + 5)
2.2000 V / 0.1 mV / ± (0.05 % + 5)
22.000 V / ± 5.0 mV / ± 5.0 mV / ± 0.1 mV / ± (0.05 % + 5) 220.00 V / 10 mV / ± (0.05 % + 5)
1000 V / 0.1 V / ± (0.1% + 5)
- AC voltage measurement (input impedance approx. 10 MΩ):
(range / resolution / accuracy 14 kHz / 10 MΩ) 1 kHz to 10 kHz / 40 Hz to 100 kHz (with LPF)
220.00 mV / 0.01 mV / ± (1.0 % + 10) / ± (1.5 % + 30) / unspecified
2,200 mV / ± 10 V / ± 10 V / ± 10 V / ± (1.5% + 30) / unspecified ± (1.2% + 50) / ± (1.2% + 50)
22,000 V / 1 mV / ± (0.8 % + 10) / ± (1.2 % + 50) / ± (1.8 % + 50)
220.00 V / ± 0.00 V / ± 0.0 mV / ± 10) / ± (1.8 % + 50) (2.0 % + 50) / ± (2.0 % + 50)
1000 V / 0.1 V / ± (1.2 % + 10) / ± (3.0 % + 50) / ± (3.0 % + 50)
- (in AC + DC voltage measurement) approx. range / resolution / accuracy ) accuracy in the range from 40 Hz to 500 Hz
2,2000 V / 0.1 mV / ± (1.8 % + 70)
22,000 V / 1 mV / ± (1.8 % + 70)
22,000 V / 1 mV / ± (1.8 % + 70)
22,000 V / ± 1.0 mV / ± 1.0 mV / ± 1.0 % 70)
1,000 V / 0.1 V / ± (4.0 % + 70)
Displays the true RMS value
- DC current measurement:
(range / resolution / accuracy)
220.00 μA / 0.01 μA / 0.01 μA / ± 1 μA,
2200.0 μA / 0.1 μA / ± (0.5 % + 10)
22,000 mA / 1 μA / ± (0.5% + 10)
220.00 mA / 10 μA / ± (0.5 % + 0/> 10 / 0.5 % + 10) (1.2 % + 50)
- AC current measurement:
(range / resolution / accuracy) accuracy in the range 40 Hz to 1 kHz / accuracy in the range 1 kHz to 10 kHz)
220.00 μA / μA / ± 0.0 % / ± 1 kHz ± (3 % + 50)
2200 μA / 0.1 μA / ± (0.8 % + 10) / ± (3 % + 50)
22 mA / 1 μA / ± (1.2 % + 10) / ± (3 % + 50) / ± (3 % + 50) / ± (3 % + 50)
22 mA / 1 μA / ± (1.2 % + 10) / ± (3 % + 50) / ± (3 % + 50)
/ 20 μA + 10) / ± (3 % + 50)
20 A / 1 mA / ± (1.2% + 10) / ± (3% + 50)
- Resistance measurement:
(range / resolution / accuracy)
220.00 Ω, / 0.00 Ω, % / ± 1 Ω
2.2000 kΩ / 0.1 Ω / ± (0.5 % + 10)
22,000 kΩ / 1 Ω / ± (0.5 % + 10)
220.00 kΩ / 10 Ω / ± (0.5 % + 10 Ω) /20/> 102 Ω /20/> ± (0.8 % + 10)
22,000 MΩ / 1 kΩ / ± (1.5 % + 10)
220.00 MΩ / 10 kΩ / ± (3.0 % + 50)
- Capacitance measurement:
02, resolution 02,
02 nF / 1 pF / ± (3.0 % + 5)
220.00 nF / 10 pF / ± (3.0 % + 5)
2.2000 μF / 100 pF / ± (3.0% + 5)
22,000 μF / ± 5.0 %
220.00 μF / 10 nF / ± (40 % + 5)
2.2000 mF / 100 nF / ± (40 % + 5)
22,000 mF / 1 μF / ± (10 % + 5)
220 μF / ±0 % (0 μF / ± 0 % 5)
- Measurement of diodes and semiconductor junctions:
the measured value is between 0.12 and 2 V and the green LED is lit: the diode is OK,
the measured value is less than 0.12 V and the red LED is lit: the diode may be damaged at the silicon junction; 0.500 to 0.800 mV
voltage resolution during this measurement: 0.001 V
- Circuit continuity measurement:
when the line resistance is ≥70 Ω, an open circuit is indicated, the buzzer does not beep, and the red indicator light is on
0 Ω the resistance circuit is unbroken. is indicated, the buzzer sounds continuously and the green indicator light is on
Overload protection: 1000 V
Resistance resolution for this measurement: 0.1 Ω
- Frequency measurement, operating range:
(range / resolution / accuracy)
10 Hz / 1 MHz to 20 MHz, 10 Hz / 20 MHz ± 0.01% + 5
0.1% to 99.9% / 0.1% / ± (2.0% + 5)
General specifications:
- Operating temperature: 0 °C – 40 °C (32 °F – 104 °F) at relative humidity
- humidity ≤ 30% at 0 °C; ≤50% at 30°C - 40°C
- storage temperature: -10°C - 50°C (14°F - 122°F)
- Operating altitude: ≤2000 m
- Electromagnetic compatibility: complies with EN61326-1: 2006 standards
- dimensions: 186 mm × 89 mm × 49 mm
- Weight: 400 g
- The device complies with the following standards:
cETLus, CAT III 1000V, CAT IV 600V, double insulation, overload protection for voltages greater than 102>1000V
1000V; EN 61326-2-2: 2013
EN 61010-1: 2010; EN 61010-2-030: 2010; EN 61010-2-033: 2012
Compliant with UL STD: 61010-1, 61010-2-030
Certified to CSA STD. C22.2 No. 61010-1, 61010-2-030, 61010-2-033
Package contents:
- UT161E multimeter with storage case
- Gold-plated CAT III test leads / CAT IV 60V / 100/100V adapter plug - Plug for measuring transistors
- USB cable for data transfer to PC
- Fuse F1: 6 x 32 mm FF 600mA H 1000 V (ø6 x 32mm) CE - in device
- Fuse F2: 6 x 25 mm FF 11A H 1000 V in device
/CE - ø6 x 32 mm) AAA batteries, R03 1.5V
- Manual in Czech, Slovak, English
Wholesale packaging:
- standard quantity per box: 20 pcs
- standard box dimensions: 480 mm x 370 mm x 325 mm
- Total box weight: 8 kg
- UNI-TREND
-
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
UNI-T UT256A Multimeter
This product comes with a 3-year warranty. The UT256A digital multimeter is a safe and reliable clamp-on meter that can replace a clamp-on multimeter. It has no moving mechanical parts, making it resistant to mechanical failure. The device has a display with a maximum reading of 6000. The use of a Hall-effect probe allows AC current to be measured up to 200A. Using the included test leads, AC and DC voltage, resistance and wire continuity can also be measured; it features a built-in non-contact AC voltage (NCV) sensor and a built-in lamp. It features data hold, automatic and manual range selection, a backlit display, frequency measurement and a low battery indicator. The maximum wire diameter that can be inserted into the clamp is 15 mm. Range overrun is indicated by a red LED, and for NCV by an audible signal. A key advantage is its resistance to drops from a height of up to 2 m. Powered by two 1.5 V AA batteries. These features make the UT256A multimeter a practical tool for the daily work of high-voltage electricians.
Product specifications:
- measurement of AC current up to 200 A and its frequency in the range of 50 Hz to 60 Hz
- AC voltage measurement up to 10 V at 10 Hz to 10 kHz
- DC voltage measurement up to 1000 V
- Resistance measurement up to 60 MΩ
- Line continuity check
- Automatic polarity display
- Option to select automatic or manual range switching
- Built-in lamp
- True RMS value on the backlit LCD display
-
measuring 35 mm x 26 mm
- hold
- powered by two 1.5 V AA batteries
- low battery indicator
- automatic switch-off after 15 minutes (function can be temporarily disabled)
Technical specifications:
AC current measurement range:
- accuracy)
200.0 A / 0.1 A / ± (1.8 % + 2) in the range from 0.2 A to 2.0 A, 50 to 60 Hz
200.0 A / 0.1 A / ± (1.8% + 3) in the range from 2.0 to 6 A, at 50 to 60 Hz
200.0 A / 0.1 A / ± (1.8 % + 5) in the range from 5.0 A to 200 A, 50 to 60 Hz
- the accuracy of frequency monitoring when measuring AC current above 20 A, in the range from 50 to 60 Hz, is ± (0.1% + - 60 Hz) at an overcurrent protection resolution of 0.1% Hz
0. 200 A
- AC voltage measurement:
(ranges / resolution / accuracy)
6,000 V / 0.001 V / ± (1.2% + 3), in the range from 10 Hz to 10 kHz
V / 0.00 ± 2 V / 6% 3), in the range from 10 Hz to 10 kHz
600.0 V / 0.1 V / ± (1.2% + 3), in the range from 10 Hz to 10 kHz
1000.0 V / 1 V / ± (1.2 % + 8), in the range from 1.2 % + 8 kHz, in the range from 10 Hz to 10 kHz
RMS voltage value in the frequency range from 45 Hz to 400 Hz
- the accuracy of frequency monitoring when measuring AC voltage in the range from 10 Hz to 10 kHz is ± (0.1% + 5) at a resolution of 0.01 Hz to 0.01 kHz, with overcurrent protection at amplitudes
- Input impedance approx. 10 MΩ
- DC voltage measurement:
(ranges / resolution / accuracy)
6,000 V / 0.001 V / ± (0.8 % +3)
60.00 V / 0.010 V / ± (0.8 % > V / 60 / 0.8 % > V / 60 / 0.8 % +3) ± (0.8 % +3)
1,000.0 V / 1 V / ± (1.0 % +5)
- overload protection at 1000 Vrms
- input impedance approx. 10 MΩ
- Resistance measurement:
(ranges / resolution / accuracy)
600.0 Ω / 0.1 Ω / ± (1.2 % + 2)
6,000 kΩ / 0.001 kΩ / ± (1.0 %/0.0 Ω / ± 0.0 Ω / ± (1.2 % + 2) 0.01 kΩ / ± (1.0 % + 2)
600.0 kΩ / 0.1 kΩ / ± (1.0 % + 2)
6,000 MΩ / 0.001 MΩ / ± (1.2 % + 2)
60.00 MΩ / 0.001 MΩ / ± (1.2 % + 2)
60.00 MΩ / 0.01 (1.0 % + 2) 5)
- overload protection at 1000 Vrms
- open-circuit voltage approx. 1 V
- Circuit continuity check:
- if the measured resistance is less than 10 Ω, the continuity circuit signal emits a buzzer
- if the measured resistance is greater than 100 Ω, the open-circuit signal does not sound a buzzer
- open-circuit voltage of approximately 1/060 V
-0 V. Ω, with a resolution of 0.1 Ω
- Overload protection at 1000 Vrms
- Non-contact electric field sensing (NCV):
- low voltage detection mode ("EFLo") for voltages <48V
- low voltage detection mode ("EFHi") for voltages >-48V: as the voltage increases, the number of segments on the display increases, the green, yellow and red LEDs flash in succession and an audible signal is emitted
General parameters:
- Operating temperature and ambient humidity: 0 °C ~ 30 °C (≤80% RH), 30 °C ~ 40 °C (≤40% RH), 40 °C ~ 40 °C (≤45% RH)
- Storage temperature and humidity: -20 °C ~ 60 °C (≤80% RH)
- Operating altitude: ≤2000m
- Electromagnetic compatibility: in an RF field of 1 V/m, there is an additional error of 5% of the range; in an RF field >1 V/m, overall accuracy is not specified
- Product dimensions: 217 x 58.8 x 38.5 mm
- net product weight: 251 g
- Product colour: red and grey
- This device is designed in accordance with IEC safety standards EN61010-1, IEC/EN61010-2-033 and EN61326-1 and complies with CAT II 1000V, CAT III 600V, double insulation.
Package contents:
- UT256A clamp multimeter: 1 pair of UT256A test leads: 1 pair of test leads. 1.5 V battery (LR6): 2 pcs
- User manual: 1 pc
Wholesale packaging:
- standard quantity per box: 20 pcs
- Standard box dimensions: 485 x 310 x 205 mm
- Standard gross weight per box: 9 kg
R. UNI-TREND
https://www.uni-trend.com/
10 - 20 days
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty. The UT622A LRC is a portable component tester for inductors, resistors and capacitors and their secondary properties: D (dissipation factor), Q (quality factor), Θ (phase angle in degrees), Θ (phase angle in radians) and ESR (equivalent series resistance). Component parameters are measured using AC voltage with a selectable frequency of 100, 120, 1000, 10000 Hz and a selectable amplitude of 0.1Vrms, 0.3Vrms, 1.0Vrms at a signal source output impedance of 100Ω. The highest measurement accuracy is 0.1%.
The device features an intuitive 2.8-inch TFT LCD display with ten-step adjustable backlight brightness, a built-in high-capacity 1800mAh Li-Pol battery, and a miniUSB connector for charging and data transfer to a computer. The maximum display value when measuring primary parameters is 99999, and the minimum value when measuring secondary parameters is 0.0001. Measurement mode – a measurement triggered by a TRI button or a command from a PC; or continuous measurement with adjustable test start rate of 20x/sec, 5x/sec, 2x/sec. 2 + 1 or 4 + 1 terminal configuration (following the purchase of UTR-L100k-H test cables).
Thanks to its technological sophistication, the device is also suitable for professional use – when used with a computer (PC), it creates a station for sorting components according to specified parameters and can be used in production lines, laboratories, etc.
parameters
:
- manual RLC meter for primary and secondary component parameters
- intuitive TFT LCD display, large backlit screen, 10 brightness levels
- display range up to 99,999
- maximum accuracy 0.1%
- option to select components based on AC voltage, tolerance 10, specified tolerance 10
1000 or 10000 Hz
- Selectable amplitude measurement voltage: 0.1Vrms, 0.3Vrms, 1.0Vrms
- selection of equivalent mode (for Z <100Ω in series, for Z > 10kΩ in parallel)
- automatic identification of built-in components
- high capacity Li-ion battery: 180 mAh
- Power supply + charging: DC adapter 5V ± 0.25V, > 1A
- operating time on a single battery charge: typically 8 hours
- functions in recording mode and data statistics: AVG, MAX, MIN
- beep when buttons are pressed: yes, button can be activated:
on/off switch
automatic switch-off: yes after 5, 15, 30, 60 minutes or off
- Data interface: mini USB
- data transfer rate to computer: 9600/19200/38400 baud
- Acoustic and visual alarm comparison of tolerance results: off, pass, fail
- alarm selection: short beep
- short beep, long beep
Open circuit or short circuit tester reset: yes
- setting of tolerance value from nominal: 1% to 20%, default 5%
- Component counting: all, compliant, non-compliant
Technical parameters:
- Primary impedance measurement range / minimum resolution parameters: range
inductance L // 0.001 μH to 9999.9 H // 1 / 0.1 / 0.01 / 0.001 μH
capacitance C // 0.001 pF to 99.999 mF // 1 / 0.1 / 0.01 / resistance R // 0.01 / 0.01 / 0.0001 Ω to 99.999 MΩ // 0.0001 Ω
Total impedance Z // 0.0001 Ω to 99.999 MΩ // 0.0001 Ω
- Measurement range of secondary impedance parameters // display range of the factor //
resolution parameters // minimum display range //
// 0.0001 to 9.9999 // 0.0001
Quality factor Q // 0.0001 to 99999 // 0.0001
phase angle in degrees Θ deg // -179.9° to 179.99° // 0.0001
phase angle in degrees Θ deg // -179.9° to 179.99° // 0.0001
phase angle in 0.0001 to 9.9999 -3.142 rad to 3.1416 rad // 0.001 rad
Equivalent resistance ESR // 0.01 mΩ to 999.99 Ω // 0.01 mΩ
- display: backlit TFT LCD display with a diagonal of 2.8 inches:
-999999999999999999999999999999999999999999999999999 0.1%
- component selection based on set tolerance: yes
- voltage measurement: AC 100, 120, 1000 or 10000 Hz
- amplitude measurement: 0.1 Vrms, 0.3 Vrms, 1.0 Vrms,
data transfer to PC: via PC software
- power supply: 1800mAh Li-Pol battery and (or) 5V ± 0.25V DC adapter, > 1A
- automatic charging management: even when the device is switched off
- Charging and data interface: mini USB
- operating environment: temperature 5 to 35°C, humidity <0% by weight
- 305g
- Product dimensions (H x W x D): 190 x 90 x 44 mm
- package dimensions: 225 x 220 x 63 mm
- Safety and EMC certification: IEC / EN61010-1: 2010, EN61326-2: 2013:- EN61326-2: 2013:- 2013
Contents of individual package:
- UT622A device: 1 pc
MANUFACTURER: UNI-TREND
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty. The UT60BT is a digital multimeter with a display range of 9999, allowing for the measurement of true RMS values of voltages and currents with both automatic and manual range selection. It features 1000V rms overload protection across all ranges; the current range is protected by a 10A / 1000V tubular fuse, 6.35 x 32mm. If you approach the limit values of ≥990.0V / ≥9.900A when measuring voltages and currents, an alarm sounds and the character ‘OL’ is displayed when the limit values are exceeded. It also allows the measurement of resistance, capacitance, temperature, frequency, duty cycle, circuit continuity and semiconductor junctions. The circuit is optimised for non-contact electric field measurement in two sub-ranges. The multimeter is equipped with a modern processor featuring a fast analogue-to-digital converter (3 conversions per second) and transmits measured values via Bluetooth using the low-energy wireless technology 802.15.4 to a mobile phone or tablet with the Connect app installed.
The entire multimeter housing is fitted with a durable, double-insulated casing and has European CE certification, meeting the safety classification CAT II 1000V / CAT III 600V. The device is suitable for use in a laboratory or workshop, as well as for general electrical work. It is powered by three standard 1.5V AAA batteries, which, thanks to their low power consumption, last up to 500 hours.
Product specifications:
- backlit display range: 9999
- voltage measurement: up to ± 1000V / DC / AC to ± rms current measurement / DC: up to ± rms AC rms
- Resistance measurement: up to 99.99MΩ
- Capacitance measurement: up to 9.999mF
- Temperature measurement: up to 250 °C with the supplied K-type probe
- Frequency measurement: up to 9.999 MHz
- Manual measurement:
- Automatic measurement:
- Manual measurement:
Hz / REL / RMS / HOLD / NCV EFLo / NCV EFHi
- Circuit continuity measurement
- Semiconductor junction measurement
- Non-contact NCV measurement
- visual and audible alarms
- Bluetooth for transmitting measured data
- input overload protection
- 0–10 A input current via fast-acting fuse
- Input impedance approx. 10MΩ for DCV, in the DCmV range then 3GΩ
- power supply: 3 x 1.5V, AAA
- Low power consumption during measurement: approx. 2 mA
- Sleep mode current consumption: <30 μA
- Battery life: 500 hours (automatic battery shut-off)
- Automatic battery shut-off indicator: 500 hours (sleep mode): yes, after 15 minutes
Technical parameters:
- DC voltage measurement (input impedance is approximately 3GΩ in the DCmV range, 10MΩ in other ranges):
(range / resolution / accuracy)
9.9090 % (± 9.90 mV / mV / ± 9.90 mV) + 8)
99.99 mV / 0.01 mV / ± (0.7% + 8)
999.9 mV / 0.1 mV / ± (0.5 % + 3)
9.999 V / 0.001 V / ± (0.5 % / 9 V / ± (0.5 % + 3)
(0.5% + 3)
999.9 V / 0.1 V / ± (0.5 % + 3)
- Maximum input voltage: ± 1000 V, alarm sounds at 990.0 V, ‘OL’ is displayed at >1000 V.
- Overload protection 1000 V AC / AC/AC
/>
Voltage measurement (input impedance approx. 10 MΩ):
(range / resolution / accuracy in the range 40 Hz to 400 Hz, RMS sine wave)
9.999 mV / 0.001 mV / ± (1 % + 3)
99.99 mV //3.01 mV //> 999.9 mV / 0.1 mV / ± (0.8 % + 3)
9.999 V / 0.001 V / ± (0.8 % + 3)
999.9 V / 0.1 V / ± (0.8 % + 3)
- Maximum input voltage 0 V, alarm 0 V, 0.10 V AC; ‘OL’ is displayed at >1000 V.
- Overload protection 1000 V RMS (DC / AC)
- DC current measurement:
(range / resolution / accuracy)
999.9 μA / 0.1 μA / ± (0.8% / mA) / 90% + 390 mA. ± (1.0% + 3)
9.999 A / 0.001 A / ± (1.0% + 3)
- Alarm sounds at ≥9,900 A, ‘OL’ is displayed at >10.00 A.
- Overload protection: 1000 V RMS,
measurement:
(range / resolution / accuracy in the range from 40 Hz to 400 Hz)
999.9 μA / 0.1 μA / ± (1.0% + 3)
999.9 mA / 0.1 mA / ± (1.2% + 0.1 mA / ± (1.2% + 3). (1.2% + 3)
- Alarm sounds at ≥9,900 A, ‘OL’ is displayed at >10,000 A.
- Overload protection: 1000 V RMS, 10 A fast-acting fuse
- Resistance measurement:
(range / resolution //>09 accuracy)
Ω / ± (0.8% + 2)
9.999 kΩ / 0.001 kΩ / ± (0.8% + 2)
99.99 kΩ / 0.01 kΩ / ± (0.8 % + 2)
999.9 kΩ / ± 0.1 kΩ / ± 0.1 kΩ / ± (0.1 kΩ)
9.999 MΩ / 0.001 MΩ / ± (1.5 % + 3)
99.99 MΩ / 0.01 MΩ / ± (2.0 % + 5)
- Overload protection 1000V
- Capacitance measurement:
Accuracy range nF 9 /
0.001 nF / ± (4% + 10)
99.99 nF / 0.01 nF / ± (4% + 5)
999.9 nF / 0.01 nF / ± (4% + 5)
9.999 µF / 0.01% / ± 5)
99.99 µF / 0.01 µF / ± (4% + 5)
999.9 μF / 0.1 μF / ± (4% + 5)
9.999 mF / 0.001 mF / ± (10%)
- For Rn-type capacitors, use Rn capacitors
1000 V overload protection
- Frequency measurement:
(range / resolution / accuracy)
99.99 Hz to 9.999 MHz / 0.01 Hz to 0.001 MHz / ± (0.1% + 5)
- Overload protection 0.00 V RMS (0.00 V DC) AC)
- Duty cycle measurement for square waves ≤10 kHz:
(range / resolution / accuracy)
0.1% to 99.9% / 0.1% / ± (3% + 5)
Overload protection 1000 V DC -
/>
test:
voltage across terminals without load approx. 3.3 V
voltage drop across a good silicon junction is 0.5 to 0.8 V
measurement resolution 0.001 V
- Circuit continuity test:
the buzzer will not sound if the resistance is lower than the sound
30 if the resistance is less than 30 Ω
Overload protection 1000V RMS (DC / AC)
- Temperature measurement:
(range / resolution / accuracy)
-40 °C to 0 °C / 1 °C / ± 4 °C
0 °C to 10 °C / ± 100 °C / (±5 °C)
100 °C to 1000 °C / 1 °C / ± (2.0% + 5)
-40 °F to 32 °F / 1 °F / ± 5 °F
> 32 °F to 212 °F / 1 °F / ± 5 °F / ± 2% / ± 5 °F
1832 °F / 1 °F / ± (2.5% + 5)
The K-type thermocouple included as an accessory is only suitable for measuring temperatures below 250 °C / 482 °F.
1000 V RMS (DC / AC) overload protection
General operating temperature:
> 40 °C
- storage temperature: -10 °C to 50 °C (14 °F to 122 °F)
- Operating relative humidity: ≤75% (0 °C to 30 °C), ≤50% (30 °C to 40 °C)
- Operating altitude: 0 m to 20 °C
- EMC resistance: for radio frequency field 1V/m
- Power supply: 3 x 1.5V, AAA
- Product colour: red and grey
- Net product weight: 290 g
- Product weight: approx. 400 g (including batteries)
- Product dimensions: 16 x 84 mm
Contents of individual package:
- UT60BT multimeter with storage case: 1 pc
- 1.5V AAA battery: 3 pcs
- F1 fuse: F 10A / 250V (6.35 x 32mm) - Category II test lead set:
1 pc 1000V / CAT III 600V: 1 pair
- temperature probe: 1 pc
- user manual: 1 pc
Wholesale packaging:
- standard quantity per box: 20 pcs
- standard box dimensions: 420 x 03>
-
- Manufacturer: UNI-TREND
-
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
The UT622C LRC device is a portable component tester — coils (inductance), resistors (resistance) and capacitors (capacitance) — and their secondary properties: D (loss factor), Q (quality factor), Θ (phase angle in degrees), Θ (phase angle in radians) and ESR (equivalent series resistance or parallel resistance). Component parameters are measured using alternating voltage with a selectable frequency of 100, 120, 1000, 10000 Hz, 100 kHz and a selectable amplitude of 0.1 Vrms, 0.3 Vrms, 1.0 Vrms at a signal source output impedance of 100Ω. The highest measurement accuracy is 0.1%.
The device features an intuitive 2.8-inch TFT LCD display with ten-level adjustable backlight brightness, a built-in high-capacity 1800mAh Li-Pol battery and a miniUSB connector for charging and data transfer to a computer. The maximum display value when measuring primary parameters is 99999, and the minimum value when measuring secondary parameters is 0.0001. Measurement mode – a measurement triggered by the TRI button or a command from a PC; or continuous measurement with adjustable test trigger rates of 20x/sec, 5x/sec, 2x/sec. 2+1 or 4+1 terminal configuration (with UTR-L100k-H test cables included with this device).
Thanks to its technological sophistication, the device is also suitable for professional use – when connected to a computer (PC), it creates a component sorting station based on specified tolerance parameters and can be used in production lines, laboratories, etc. Intuitive TFT LCD display, 10 brightness levels
- display range up to 99,999
- maximum accuracy 0.1%
- Ability to select components according to specified tolerance
- AC voltage measurement: 100, 120, 1000 Hz / 0–1000 Hz amplitude measurement. Voltage: 0.1 Vrms, 0.3 Vrms, 1.0 Vrms
- selection of equivalent mode (for Z <100Ω in series, for Z >10kΩ in parallel)
- automatic component identification
- built-in high-capacity Li-Pol battery: 3.7V/1800 mAh: DC +5V charging power supply
±0.25V, >1A
- operating time on a single battery charge: typically 8 hours
- Functions in data logging and statistics mode: AVG, MAX, MIN
- Audible tone when buttons are pressed: yes, can be disabled/enabled
- button lock option: yes
1, 6, automatic after shutdown minutes, or off
- Data interface: mini USB
- Data transfer rate to PC: 9600/19200/38400 baud
- Audible and visual alarm for tolerance comparison results: off, pass, fail
- Audible alarm selection: short beep, long beep, two short beeps
in case of open circuit or short circuit reset
: yes
- Setting of tolerance value from nominal: 1% to 20%, default 5%
- Component counting: all, compliant, non-compliant
Technical parameters:
- Measurement range for primary impedance parameters:
type // minimum resolution within the display range 0.001 μH to 9999.9 H // 1 / 0.1 / 0.01 / 0.001 μH
capacitance C // 0.001 pF to 99.999 mF // 1 / 0.1 / 0.01 / 0.001 / 0.001 pF at 0.001 pF resistance ///>0.0 R0.0. 99.999 MΩ // 0.0001 Ω
Total impedance Z // 0.0001 Ω to 99.999 MΩ // 0.0001 Ω
- Measurement range of secondary impedance parameters:
type // minimum resolution // 0.000 display range ////0000 display range 9.9999 // 0.0001
Quality factor Q // 0.0001 to 99999 // 0.0001
phase angle in degrees Θ degrees // -179.9° to 179.99° // 0.01°
phase angle in rad / 2 radians -Θ. 3.1416 rad // 0.001 rad
Equivalent resistance ESR // 0.01 mΩ to 999.99 Ω // 0.01 mΩ
- display: backlit TFT LCD display with a diagonal of 2.8" and a resolution of 320 x 240 pixels
-9999999 pixels. Accuracy: best 0.1%
- Component selection based on set tolerance: yes
- voltage measurement: AC 100, 120, 1000, 10000 Hz or 100 kHz
- Voltage amplitude measurement: 0.1 Vrms, Vrms, 0.1 Vrms, data transfer 0.1 Vrms, 0. Yes, after installing the software on a PC
- power supply: 1800mAh Li-Pol battery and/or 5V ±0.25V DC adapter, >1A
- automatic charging management: even when the device is switched off
- Charging and data interface: mini USB
- Operating environment: temperature 5 to 35°C, humidity ≤ 35% - Weight with/without battery: 305g / 420g
- Product dimensions (H x W x D): 192 x 93 x 44 mm
- Package dimensions: 225 x 220 x 63 mm
- Safety and EMC certification: IEC/EN 61010-1: 2010, EN 2013206, EN 61326-2-2: 2013
Contents of individual package:
- UT622C device: 1 pc UTR-001 box: 1 pc
- user manual: 1 pc
Packaging for bulk customers:
- standard quantity per box: 10 pcs
- standard box dimensions: 370 x 305 x 475 mm
- gross weight of 2 cartons: 2 kg
MANUFACTURER: UNI-TREND
10 - 20 days
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty. The UT622E LRC is a portable component tester for inductors, resistors and capacitors, measuring overall impedance Z and DC resistance DCR, as well as their secondary properties: D (loss factor), Q (quality factor), Θ (phase angle in degrees), Θ (phase angle in degrees), Θ (phase angle in series or equivalent radians (resistors) and ESR (parallel resistance). Component parameters are measured using AC voltage with a selectable frequency of 100 Hz, 120 Hz, 1 kHz, 10 kHz, 100 kHz and a selectable amplitude of 0.1 Vrms, 0.3 Vrms, 1.0 Vrms at a signal source output impedance of 1100Ω. Unlike the UT622A, the UT622E also offers the option to measure using a DC voltage of 1.0 V. The highest measurement accuracy is 0.1%.
The device features an intuitive 2.8-inch TFT LCD display with ten-step adjustable backlight brightness, a built-in high-capacity 1800mAh Li-Pol battery, and a miniUSB connector for charging and data transfer to a computer. The maximum display value when measuring primary parameters is 99999, and the minimum value when measuring secondary parameters is 0.0001. Measurement mode – a measurement triggered by a TRI button or a command from a PC; or continuous measurement with adjustable test start rate of 20x/sec, 5x/sec, 2x/sec. Terminal configuration 4 + 1n (UTR-L100k-H) or 2 + 1 (after purchasing UTR-002 test cables with crocodile clips).
Thanks to its technological sophistication, the device is also suitable for professional use – together with a computer (PC), it creates a station for sorting specified parameters in laboratories, production lines and is compliant with laboratory standards, etc.
Product parameters:
- manual RLC meter for primary and secondary component parameters
- intuitive TFT LCD display, large backlight, 10 brightness levels
- display range up to 99,999
- Maximum accuracy for specified components
- 1% selectable
/- 1% selectable for components measuring AC voltage at 100 Hz, 120 Hz, 1 kHz, 10 kHz, 100 kHz
- Selectable AC voltage range: 0.1 Vrms, 0.3 Vrms, 1.0 Vrms
- DCR measurement capability with 1.0 V DC-equivalent in series, for Z > 10 kΩ in parallel)
- automatic component identification
- Built-in high-capacity Li-Pol battery: 1800 mAh
- Power supply + charging: DC adapter 5V ± 0.25V, > 1A
- Operating time on a single battery charge: typically 8 hours, including AV-G recording and statistics functions
MIN
- beep when buttons are pressed: yes, can be switched on/off
- button lock: yes
- auto-off: yes, after 5, 15, 30, 60 minutes or off
- Data interface: mini USB
- data transfer rate to PC: 94,000/3,000,000,000 comparison of audible and visual tolerance results: off, pass, fail
- audible alarm selection: short beep, long beep, two short beeps
- Open circuit or short circuit tester reset: yes
- Setting of tolerance value from nominal: 1% to 20%, default 5%
- Counting of all components: non-compliant
Technical parameters:
- Measurement range for primary impedance parameters:
type // display range // minimum resolution in the
inductance L // 0.001 μH to 9999.9 H // 1 / 0.01 μ / 0.001 μ /
capacitance C // 0.001 pF to 99.999 mF // 1 / 0.1 / 0.01 / 0.001 pF
resistance R // 0.0001 Ω to 99.999 MΩ // 0.0001 Ω
Total impedance
0909/0Ω. // 0.0001 Ω
DC resistance DCR // 0.1 mΩ to 999.99 kΩ // 0.1 mΩ
- Measurement range for secondary impedance parameters:
type // display range // minimum resolution within the range
D loss factor // 9/90000000 // 1 // 9000000. 0.0001
Quality factor Q // 0.0001 to 99999 // 0.0001
phase angle in degrees Θ // -179.9° to 179.99° // 0.01°
phase angle in radians Θ / 1 rad // 6 rad // 3.1 rad // 0.001 rad
Equivalent resistance ESR // 0.01 mΩ to 999.99 Ω // 0.01 mΩ
- display: backlit TFT LCD display with a diagonal of 2.8"
- display range: maximum 99999
- component setting accuracy
- 1%: tolerance in accordance with best fit
-. yes
- Measurement in DCR mode: DC voltage 1.0V
- AC voltage measurement: AC 100 Hz, 120 Hz, 1 kHz, 10 kHz, 100 kHz
- measurement voltage range: 0.1 Vrms, 0.3 Vrms, data transfer 0.3 Vrms,
Vrms, yes, after installing the software on the PC
- Power supply: 1800mAh Li-Pol battery and (or) 5V ± 0.25V DC adapter, > 1A
- automatic charging management: even when the device is switched off
- Charging and data interface: mini USB
- operating environment: temperature 5 to 80°C, humidity ≤ 30% without batteries: 305g
- Product dimensions (H x W x D): 190 x 90 x 44 mm
- Package dimensions: 225 x 220 x 63 mm
- Safety and EMC certification: IEC / EN61010-1: 2010, EN61326-2:-2:-2:6 2013
Contents of individual package:
- UT622E device: 1 pc
- USB interface cable: 1 pc
- UTR-L100k-H four-pole test leads: 1 pc
- Gold-plated short-circuit test lead: UTR-1-circuit
1 pc
MANUFACTURER: UNI-TREND
10 - 20 days
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty.
The UT196 True RMS solar multimeter from UNI-T is a professional-grade product designed for professionals who install or maintain photovoltaic or wind power plants. The device’s design allows it to operate in harsh outdoor environments – it has IP65 protection and can withstand a drop from a height of 2 m. This multimeter measures DC voltage up to 1700 V and AC voltage (true RMS) up to 1500 V at a frequency range of 45 to 1000 Hz. With the optional UT-CS09D Flex current loop, it allows non-contact measurement of AC currents from 1.5 to 3000 A, even in confined spaces. In addition, the UT196 measures frequency, resistance, capacitance, semiconductor transitions and electrical circuit continuity.
The low-pass function allows you to filter out RF interference generated by the inverter. The low-impedance mode can help with troubleshooting sensitive circuits, as well as circuits that may contain stray voltages. A built-in torch, a bright backlight, and audible and visual alarms allow users to complete their work safely and efficiently, even in dark and noisy environments.
The UT196 solar digital multimeter is designed with overload protection of 1700V DC, 1500Vrms AC and tested for safe use in a CAT III 1000V, CAT IV, UK and CA600V, UK and CA 600Vrms certified environment. cETLus.
Product specifications:
- Multifunctional multimeter designed for use in both outdoor and indoor photovoltaic and wind power installations
- measurement of AC/DC voltage, resistance, capacitance, frequency, diodes, circuit continuity, with external current loop and AC current
- LCD display
-, backlit maximum value
-- display: ± 6000, values are updated 2 to 3 times per second
- analogue bar graph: yes, 31 segments, measurement rate of 30 times per second
- range switching: automatic / manual
- automatic AC/DC voltage detection: yes
- non-contact electromagnetic field measurement (NCV): yes
- diode testing (semiconductor junctions): yes, open-circuit voltage approx. 3V
- electrical circuit continuity test: yes, the circuit is considered closed when R ≤ 10Ω, then the buzzer emits a beep
- built-in low-pass filter (LPF): yes, when the LPF is activated, interfering voltages above 1.2 kHz are attenuated by ≥ -3 dB/0>Hz relative to the measured attenuationHz. yes
- Peak Hold: yes
- Data Hold: yes
- Max/Min mode: yes
- Power supply: 9V battery / 6F22,
- Low battery indication: yes, when voltage drops below <7.5V, - automatic switch-off during inactivity
-1
- minutes
- Built-in torch: yes
- audible and visual indicator: yes
Technical parameters:
DC voltage measurement (V): Range / Resolution / Accuracy
600.0 mV / 0.1 mV / ±(0.5%/1 V/5.0)
±(0.2%+5)
60.00 V / 0.01 V / ±(0.2% + 5)
600.0 V / 0.1 V / ±(0.2% + 5)
1700V / 1V / ±(0.2%+5)
The input range is approximately mV/DC. 1GΩ.
AC voltage measurement (V): Range / Resolution / Accuracy
600.0 mV / 0.1 mV / 45 Hz to 500 Hz: ± (0.8%+3); 500 Hz to 1 kHz: ± (1.8%+3)
6.000V / 0.001V / 45Hz to 500Hz: ± (0.8%+3); 500Hz to 1kHz: ± (1.8%+3)
60.00 V / 0.01 V / 45 Hz to 500 Hz: ± (0.8% + 3); 500 Hz to 1 kHz: ± (1.8% + 3)
600.0V / 0.1V / 45Hz to 500Hz: ± (0.8%+3); 500Hz to 1kHz: ± (1.8%+3)
1500 V / 1 V / 45 Hz to 500 Hz: ± (0.8% + 3); 500 Hz to 1 kHz: ± (1.8% + 3)
Input impedance in the mV/AC range is approx. 10MΩ.
Automatic AC/DC voltage measurement: automatic range / Resolution / Accuracy
0V to 600.0V / 0.1V / DC to 500Hz: ± (2.0%+3); 500 Hz to 1 kHz: ± (4.0%+3)
With automatic range selection, LPF, Peak Hold selection is not possible; the input impedance is 2 MΩ
Resistance measurement: range / resolution / accuracy
600.0Ω / 0.10Ω / ±20.10Ω / ±20.10Ω 1Ω / ± (0.8%+2)
60.00 kΩ / 10 Ω / ± (0.8% + 2)
600.0 kΩ / 100 Ω / ± (0.8% + 2)
6,000 MΩ / 1 kΩ / ± (1.2%/+6 Ω)<0br/>+3 Ω. (2.5%+5)
Capacitance measurement: Range / Resolution / Accuracy
60.00 nF / 0.01 nF / in REL mode: ± (3%+10)
600.0 nF / 0.1 nF / ± (1.9% > +5.00 μF / 0.00 μF / 0.00 μF / 5.00 μF) ± (1.9% + 5)
60.00 μF / 0.01 μF / ± (1.9% + 5)
600.0μF / 0.1μF / ± (1.9%+5)
6,000 mF / 0.001 mF / ± (5% > +5)
0.001 mF / 0.001 mF / ± (5% >+5) ± (5%+5)
Measurement of AC currents with a UT-CS09D Flex current loop: Range / Resolution / Accuracy
30.00A / 0.01A / ± (0.8%+8)
300.0A / 0.1A /+300.0A / 0.1A /+0. ± (0.8%+8)
Frequency measurement: Range / Resolution / Accuracy
60.00 Hz to 1,000 MHz / 0.1 Hz to 0.001 MHz / ± (0.08% +4)
Other operating parameters: -0.001 MHz 40°C (32°F – 104°F)
- Storage temperature: -10°C to 50°C (14°F to 122°F)
- relative humidity: ≤75% RH (0°C - 30°C), ≤50% RH (30°C) operating altitude -
≤2000m
- EMC immunity: in accordance with EN61326-1: 2013, EN61326-2-2: 2013
- Power supply: 9V battery / 6F22
- External dimensions: 195 x 95 x 58 mm
- Weight: 4–85 g
- Drop test: 2m
- Certification: CE, UKCA, cETLus (CAT III 1000V, CAT IV 600V)
- Complies with standards: EN61010-1, EN61010-2-033, EN/IEC 61010-031 :-Contents of individual packaging :-/>
UT196 Solar PRO multimeter: 1 pc
- test leads: 1 pair
- 9V/6F22 battery: 1 pc
- user manual: 1 pc
Manufacturer:
UNI-TREND
-
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty. The UT256 is an easy-to-use, non-contact AC/DC current clamp meter, rated up to 60A CAT III 600V, with automatic True RMS measurement. The fork-shaped clamping head design allows for more convenient current measurement on wires up to 10 mm in diameter. It can detect the presence of voltage via an integrated non-contact voltage (NCV) sensor at the tip of the fork. Thanks to the audio and visual alarm function, this device allows you to obtain measurement results more intuitively. The specially designed slim body and slim fork are very useful for measuring cables in confined spaces.
Thanks to its modern appearance, durable design and features such as LCD backlighting, REL, ZERO and HOLD, the UT256 is an ideal measuring tool. The multimeter comes with two 1.5 V AAA batteries that are easy to replace, and the easy-access door is designed for quick battery replacement.
The multimeter is designed in accordance with safety standards IEC/EN61010-1, 61010-2-032 and electromagnetic compatibility standard EN61326-1, and meets the 00V double insulation safety standard and insulation class III. 2; it is intended for indoor use.
Product parameters:
- AC/DC current measurement
- Non-contact voltage detection (NCV) in wires or terminals
- Backlit LCD display, maximum display value is 600
- Audible and visual alarm accuracy guaranteed in the range of 1A to 60A
- Powered by two 1.5V AAA R03 batteries
Technical parameters:
To ensure measurement accuracy, the operating temperature should be within the range of 18°C – 28°C
1. AC current measurement (ranges/resolution/accuracy):
60.0A / 0.1A / 1.0A to 3.0A accuracy ±(2%+10)
60.0A / 0.1A / 3.0A to 60.0A, accuracy ±(2%+5)
Accuracy ±(2%+5)
A in the 60.0A range is guaranteed for frequencies from 50 Hz to 60 Hz.
2. DC current measurement (ranges/resolution/accuracy):
60.0A / 0.1A / 1.0A up to 3.0A accuracy ±(2%+10)
60.0A / 0.1A / 3.0A up to 60.0A, accuracy ±(2%+5)
Accuracy is guaranteed in the range from 1 to 1A. 60A.
3. Non-contact electric field sensor (NCV):
- enables acoustic detection of live conductors using a buzzer and optical detection using an LED
Other parameters:
- fork opening: 10 mm
- measurement in REL mode: yes
- measurement of actual current values: yes
yes
- value reset: yes
- low battery indicator: yes
- automatic switch-off: yes, after approx. 30 minutes
- drop resistance: yes, 2 m with functionality guarantee
- electromagnetic compatibility: RF≤1V/m overall accuracy = declared accuracy ±5% of the range; if RF>1V/m, accuracy is not specified
- certificates: CE, UKCA, cETLus operating altitude
-0/m
-0/m operating temperature and humidity: 0 to +30°C (≤ 80%RH), 30 to 40°C (≤ 75%RH), 40 to 50°C (≤ 45%RH)
- Storage temperature and humidity: -20 to +60°C (≤ 80%RH)
- Recommended battery life: 2 years:
- 1 year with 1.5 V AAA batteries (R03)
- Product dimensions: 171 × 42 × 28 mm
- UT256 weight: approx. 120g (including batteries)
- Product colour: red and grey
Package contents:
- UT256 clamp multimeter: 1 pc
- 1.5 V battery (R03): 2 pcs
- user manual: 1 pc
- carrying case
- pcs
Wholesale packaging:
- standard quantity per box: 40 pcs
- Standard box dimensions: 380 x 225 mm x 290 mm
- standard gross weight of box: approx. 14 kg
Manufacturer:
UNI-TREND
-
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty. The UT60EU is a digital multimeter with a display range of 9999, enabling the measurement of true RMS voltage and current values with both automatic and manual range selection. It features 1000V rms overload protection across all ranges; the current range is protected by a 10A / 1000V tube fuse, 6.35 x 32mm. If you approach the limit values of ≥990.0V / ≥9.900A when measuring voltages and currents, an alarm will sound and ‘OL’ will be displayed when the limit values are exceeded. In addition, it allows the measurement of resistance, capacitance, temperature, frequency, duty cycle, circuit continuity and semiconductor junctions. The circuit for non-contact electric field measurement in two sub-ranges is optimised. The multimeter is equipped with a modern processor featuring a fast analogue-to-digital converter (conversion rate of 3 times per second).
The entire structure of the multimeter is fitted with a durable, double-insulated casing and has European CE certification, meeting the safety classification CAT II 1000V/CAT III 600V. The device is suitable for use in a laboratory or workshop, as well as for general electrical work. It is powered by standard 3 x 1.5V AAA batteries, which last up to 500 hours thanks to low power consumption.
Product specifications:
- backlit display range: 9999
- voltage measurement: up to ±1000V / DC / DC / AC / rms measurement: up to 1000V / DC / AC / AC rms: up to 1000V rms
- Resistance measurement: up to 99.99MΩ
- Capacitance measurement: up to 9.999mF
- Temperature measurement: with supplied K-type probe up to 250°C
- Frequency measurement: up to 9.999 MHz
- Manual measurement:
- Manual measurement: up to duty cycle/1kHz / REL / RMS / HOLD / NCV EFLo / NCV EFHi
- Circuit continuity measurement
- Semiconductor junction measurement
- Non-contact NCV measurement
- visual and audible alarms
- Voltage input protection against input overloads exceeding 10/100V
- A00V fuse
- input impedance approx. 10MΩ for DCV, then 3GΩ in the DCmV range
- Power supply: 3 x 1.5V, AAA
- Low power consumption during measurement: approx. 2 mA
- Standby current: < 30 μA
- operates on a set of batteries
- Automatic 0-hour battery indicator
- 500 hours
shutdown (sleep mode during inactivity): yes, after 15 minutes
Technical parameters:
- DC voltage measurement (input impedance is approximately 3GΩ in the DCmV range, 10MΩ in the other ranges):
(range / resolution / accuracy)
± 0V /m909 / ± 0V (0.7% + 8)
99.99 mV / 0.01 mV / ± (0.7% + 8)
999.9 mV / 0.1 mV / ± (0.5% + 3)
9.999 V / 0.001 V / 0.001 V / +95% /> ± (0.5% + 3)
0.1 V / ± (0.5% + 3)
999.9 V / 0.1 V / ± (0.5% + 3)
- Maximum input voltage: ±1000V, alarm sounds at 990.0V, ‘OL’ is displayed at >1000V.-MS overload protection
- AC voltage measurement (input impedance approx. 10MΩ):
(range / resolution / accuracy in the range 40Hz to 400Hz, sinusoidal RMS)
9.999 mV / 0.001 mV / ± 9.999 mV / 0.001 mV / ± 9.9% 0.01 mV / ± (1% + 3)
999.9 mV / 0.1 mV / ± (0.8% + 3)
9.999 V / 0.001 V / ± (0.8% + 3)
99.99 V / ± 0.1 V / 0.1 V
999.9 V / 0.1 V / ± (0.8% + 3)
- Maximum input voltage: 1000 V AC, alarm sounds at 990.0 V, ‘OL’ is displayed at > 1000 V.
- 1000 V RMS (DC/AC) overload protection (DC/AC) overload protection
-
-
Current measurement accuracy range )
999.9 μA / 0.1 μA / ± (0.8% + 3)
999.9 mA / 0.1 mA / ± (1.0% + 3)
9.999 A / 0.001 A / ± (1.0% + 3)
will sound at 9.0% + 3). ‘OL’ will be displayed at >10.00A
Overload protection: 1000V RMS, 10A fast-acting fuse
- AC current measurement:
(range / resolution / accuracy in the range 40Hz to 400Hz)
999.00% /±0.3)
999.9mA / 0.1mA / ± (1.2% + 3)
9.999 A / 0.001 A / ± (1.2% + 3)
Alarm will sound at ≥9.900 A, ‘OL’ will be displayed at load >10/0000000000000000000 protection. RMS, 10 A fast-acting fuse
- Resistance measurement:
(range / resolution / accuracy)
999.9 Ω / 0.1 Ω / ± (0.8% + 2)
9.999 kΩ / 0.001 kΩ / 0.001 kΩ / 0.001 kΩ / 0.001 kΩ / ± 9 Ω / ± 9 Ω / 0.1 Ω / ± (0.8% + 2) kΩ / 0.01 kΩ / ± (0.8% + 2)
999.9 kΩ / 0.1 kΩ / ± (0.8% + 2)
9.999 MΩ / 0.001 MΩ / ± (1.5% + 3)
99.999 MΩ / 0.001 MΩ / ± (1.5% + 3)
99.99. 5)
1000V overload protection
- Capacitance measurement:
(range / resolution / accuracy)
9.999 nF / 0.001 nF / ± (4% + 10)
99.99 nF / ± 0.001 nF / ± (4% + 10)
99.99 nF / ± 5% (1 nF / ± 5) (1 nF / ± 0 / ± 0). 999.9 nF / 0.01 nF / ± (4% + 5)
9.999 µF / 0.001 µF / ± (4% + 5)
99.99 µF / 0.01 µF / ± (4% + 5)
99.99 µF / 0.01 µF / ± (4% + 5) 9.999 mF / 0.001 mF / ± (10%)
For capacitances ≤100nF, use the REL module
1000V overload protection
- Frequency measurement:
(range/resolution/accuracy) 99.99 MHz/
Hz. 0.01 Hz to 0.001 MHz / ± (0.1% + 5)
1000 V RMS (DC/AC) overload protection
- Duty cycle measurement for square waves ≤10 kHz:
(range / resolution / accuracy)
9.1% / ± 0.9% / 9.1% / 0.001 MHz / ± (0.1% + 5) 5)
Overload protection 1000 V RMS (DC/AC)
- Diode test:
voltage across terminals without load approximately 3.3 V
voltage drop across a good silicon junction is 0.5 to 0.8 V
measurement resolution 0.001 V
/>
/>
a beep will sound if the resistance is less than 30 Ω
Overload protection 1000 V RMS (DC/AC)
- Temperature measurement:
(range / resolution / accuracy)
°C /°C / ± 0°C /°C ± 0°C 4°C
0°C to 100°C / 1°C / ± (1.0% + 5)
100°C to 1000°C / 1°C / ± (2.0% + 5)
-40°F to 32°F / 1°F / ± 2°F /°F / ±/> 1°F / ± (1.5% + 5)
>212°F – 1832°F / 1°F / ± (2.5% + 5)
The K-type thermocouple accessory is only suitable for temperature measurements below 250°C/482°F. Features:
- Operating ambient temperature: 0°C to 40°C
- Storage temperature: -10°C – 50°C (14°F – 122°F)
- Operating relative humidity: ≤75% (0°C to 30°C), ≤50% (30°C to operating altitude)
- 0°C at 2000m
- operating environment: indoor use
- EMC resistance: for radio frequency field 1V/m
- power supply: 3 x 1.5V, AAA
- LCD display: 73 mm x 50 mm with backlight, 2 brightness levels, or off
- product colour: red and grey: 20 g
- Product weight: approx. 400 g (including batteries)
- Product dimensions: 169 x 81 x 46 mm
Contents of individual package:
- UT60EU multimeter with storage case: 1 pc
- 1.5V AAA battery: 3 pcs. /250V (6.35 x 32 mm) - in the device: 1 pc
- Test leads with CAT II 1000V/CAT III 600V category tips: 1 pair
- temperature probe: 1 pc
- user manual: 1 pc
Standard packaging:
Qty
- Standard carton dimensions: 420 x 320 x 300 mm
- Manufacturer: UNI-TREND
-
10 - 20 days
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty. The UT18B MAX digital multimeter is a reliable True-RMS digital multimeter. Designed to withstand interference, the multimeter can filter out interference from the carrier frequency superimposed on a sinusoidal wave signal or a variable voltage distortion signal, and is capable of measuring the output voltage of a variable frequency converter. In DC/AC voltage mode, the instrument can perform frequency and duty cycle measurements. The UT18B MAX features a temperature measurement function with a resolution of 0.1 °C. The LED test function allows the UT18B MAX to test LEDs with a voltage of up to 12 V without the need to determine polarity.
The UT15B/17B/18B MAX True RMS Multimeter series features fast response, standard EMC interference protection and a robust, portable design with a compact, interference-resistant build. Gold-plated test leads and fine-tip gold-plated test leads are included. They are also equipped with 1000 V input protection, making them an ideal tool for electronics and electrical engineers. Certifications: CE, UKCA, cETLus, REACH, RoHS
Product parameters:
- Large LCD display, 6000-count analogue-digital display, fast ADC refresh rate: 5 times per second
- Built-in VFD for accurate measurement of automatic/variable frequency bias voltage; relative measurement mode output for capacitance over 6.2 μF
- Full protection against false detection, allowing it to withstand a maximum overvoltage of 1000 V; designed with overvoltage and overcurrent indication
- designed with an LED measurement function (output: 12V) for automatic polarity identification
- the current input terminal is equipped with audible and visual indicators for incorrect connection
- two test probes (standard and fine tip)
- two backlight modes (high/low brightness).
- when the memory switch is in the current/as current position, - when the memory switch is in the current position. activated.
Technical parameters:
- DC voltage measurement ranges (DC current): 600 mV / 6 V / 60 V / 600 V / 1000 V ±(0.4%+3)
- DC voltage measurement ranges (AC current): 60 / 60 V / 60 V / 60 V / 60 V / 1000 V ±(0.5%+5)
- VFD (voltage): 600 V ±(8%)
- AC current measurement ranges (alternating current): 600 μA / 6000 μA / 60 mA / 600 mA / 6 A / 6 A / ± 3.5 A / ± 3(1.2 A / ± 3) current (direct current): 600 μA / 6000 μA / 60 mA / 600 mA / 6 A / 10 A ±(1.2%+3)
- resistance measurement ranges: 600 Ω / 6 kΩ / 60 kΩ / 600 kΩ / 600 kΩ / 600 kΩ / 600 kΩ ±2)
0. Frequency measurement range: 10 Hz to 10 MHz ±(0.1%+3)
- duty cycle measurement range: 1% to 99.9% ±(1.0%+4)
- Temperature measurement range: -55 °C to 500 °C
- HTN-type LCD display with a maximum test mode of 6:00:00 HOLD
- Relative measurement mode
- Backlight (adjustable)
- Automatic or manual setting ranges
- Auto-off (sleep mode during inactivity)
- low battery indicator
- audible and visual alarm
- LED test
- incorrect connection alarm
- Category: CATⅢ 2/60 CATⅢ power supply
1.5V batteries
- weight: 455 g
- dimensions: 182 mm x 91 mm x 45 mm
- accessories: 1 user manual, 2 pairs of test leads (standard gold-plated probe and fine-tip probe), 1 K-type thermocouple, 2 batteries.
10 - 20 days
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty. The UT15B MAX digital multimeter is a reliable True-RMS digital multimeter. Designed to withstand interference, the multimeter can filter out interference from the carrier frequency superimposed on a sinusoidal wave signal or a variable voltage distortion signal, and is capable of measuring the output voltage of a variable frequency converter. In DC/AC voltage mode, the instrument can perform frequency and duty cycle measurements.
The UT15B/17B/18B MAX series True RMS multimeters feature a compact and portable design, fast response, strong protection against EMC interference, and come with standard gold-plated test leads and fine gold-plated test leads. They are also equipped with 1000 V input protection, making them an ideal tool for electronics and electrical engineers. Certifications: CE, UKCA, cETLus, REACH, RoHS
Product specifications:
- Large LCD display, 6000-count analogue-digital display, fast ADC refresh rate: 5 times per second
- Built-in VFD for precise measurement of automatic/variable frequency bias voltage; output from relative measurement mode for capacitance over 6.2 μF in relative measurement mode
- Ability to capture maximum/minimum (MAX/MIN) values during voltage, current and resistance measurement
- full protection against false detection, enabling it to withstand a surge voltage of up to 1000 V; designed with overvoltage and overcurrent indication
- the current input terminal is equipped with audible and visual indicators for incorrect connection
- two test probes (standard and fine-tip)
- LED indication for high test voltage (≥30 V).
- Two backlight modes (high/low brightness).
- When switching positions, the AC/DC memory function is activated.
Technical parameters:
- DC voltage measurement ranges (direct current): 600 mV / 6 V / 60 V / 600 V / 1000 V ±(0.4%+3)
- DC voltage measurement ranges (AC current): 60 / 60 V / 60 V / 60 V / 60 V / 1000 V ±(0.5%+5)
- VFD (voltage): 600 V ±(8%)
- AC current measurement ranges (alternating current): 600 μA / 6000 μA / 60 mA / 600 mA / 6 A / 6 A / ± 3.5 A / ± 3(1.2 A / ± 3) current (direct current): 600 μA / 6000 μA / 60 mA / 600 mA / 6 A / 10 A ±(1.2%+3)
- resistance measurement ranges: 600 Ω / 6 kΩ / 60 kΩ / 600 kΩ / 600 kΩ / 600 kΩ / 600 kΩ ±2)
0. Frequency measurement range: 10 Hz to 10 MHz ±(0.1%+3)
- Duty cycle measurement range: 1% to 99.9% ±(1.0%+4)
- HTN-type LCD display with a maximum display of 6000
- Diode test
- Mode: MAX/MIN background measurement mode
- MAX/MIN measurement (adjustable)
- Automatic or manual setting ranges
- Auto-off (sleep mode during inactivity)
- low battery indicator
- Audible and visual alarm
- incorrect connection alarm
- category: CATⅢ 600V
- Power supply: 2 x R6 1.5 V batteries - Battery weight:
5 V - weight:
5 V 182 mm x 91 mm x 45 mm
- accessories: 1 user manual, 2 pairs of test leads (standard gold-plated probe and fine-tip probe), 2 batteries.
10 - 20 days
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty. The UT17B MAX digital multimeter is a reliable True-RMS digital multimeter. Designed to withstand interference, the multimeter can filter out interference from the carrier frequency superimposed by a sinusoidal wave signal or a variable voltage distortion signal and is capable of measuring the output voltage of a variable frequency converter. In DC/AC voltage mode, the instrument can perform frequency and duty cycle measurements. The UT17B MAX features a temperature measurement function with a resolution of 0.1 °C.
The True RMS multimeters in the UT15B/17B/18B MAX series feature a compact and portable design, fast response, strong protection against EMC interference, and come with standard gold-plated test leads and fine gold-plated test leads. They are also equipped with 1000 V input protection, making them an ideal tool for electronic and electrical engineers. Certifications: CE, UKCA, cETLus, REACH, RoHS
Product specifications:
- Large LCD display, 6000-count analogue-digital display, fast ADC refresh rate: 5 times per second
- Built-in VFD for precise measurement of automatic/variable frequency bias voltage; output from relative measurement mode for capacitance over 6.2 μF in relative measurement mode
- Ability to capture maximum/minimum (MAX/MIN) values during voltage, current and resistance measurement
- full protection against false detection, enabling it to withstand a surge voltage of up to 1000 V; designed with overvoltage and overcurrent indication
- the current input terminal is equipped with audible and visual indicators for incorrect connection
- two test probes (standard and fine-tip)
- LED indication for high test voltage (≥30 V).
- Two backlight modes (high/low brightness).
- When switching positions, the AC/DC memory function is activated.
Technical parameters:
- DC voltage measurement ranges (direct current): 600 mV / 6 V / 60 V / 600 V / 1000 V ±(0.4%+3)
- DC voltage measurement ranges (AC current): 60 / 60 V / 60 V / 60 V / 60 V / 1000 V ±(0.5%+5)
- VFD (voltage): 600 V ±(8%)
- AC current measurement ranges (alternating current): 600 μA / 6000 μA / 60 mA / 600 mA / 6 A / 6 A / ± 3.5 A / ± 3(1.2 A / ± 3) current (direct current): 600 μA / 6000 μA / 60 mA / 600 mA / 6 A / 10 A ±(1.2%+3)
- resistance measurement ranges: 600 Ω / 6 kΩ / 60 kΩ / 600 kΩ / 600 kΩ / 600 kΩ / 600 kΩ ±2)
0. Frequency measurement range: 10 Hz to 10 MHz ±(0.1%+3)
- duty cycle measurement range: 1% to 99.9% ±(1.0%+4)
- Temperature measurement range: -55 °C to 500 °C
- HTN-type LCD display with a maximum test mode of 6:00:00 HOLD, MAX/MIN
- Relative measurement mode
- Backlight (adjustable)
- automatic or manual setting ranges
- Auto-off (sleep mode during inactivity)
- low battery indicator
- audible and visual alarm
- incorrect connection alarm
- category: CATⅢ 2/00V power source
- 6 batteries
- weight: 455 g
- dimensions: 182 mm x 91 mm x 45 mm
- accessories: 1 user manual, 2 pairs of test leads (standard gold-plated probe and fine-tip probe), 1 type K thermocouple, 2 batteries.
10 - 20 days
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty. The UT117C multimeter is a high-precision True RMS digital multimeter featuring 600V AC/DC voltage measurement, 10A AC/DC current measurement, LPF measurement, Bluetooth functionality, and more. The main features are fast response, high precision, compact size and ease of use, and the product’s accuracy is guaranteed even after a 2-metre drop. It is a good tool for electricians. The UT117C is equipped with an LCD digital display, overload protection across all ranges and a unique design.
Product specifications:
- measurement of voltage, AC/DC current, resistance, capacitance, diode test, continuity and frequency
- Connection to an external current probe (ratio: 1mV/A)
- Data Hold/DC/DC – automatically identifies voltage/DC, NCV signal and current
- Auto power-off
- High-resolution A/D converter and data processing technology
- True RMS to ensure accurate measurement of non-linear loads
- Capable of measuring 20A (transient measurement within 10 seconds)
- LoZ function: low impedance, which prevents incorrect readings
- LPF function to ensure accurate measurement of voltage and frequency of the variable speed drive (VSD)
- Display of MAX/MIN average values for recording signal fluctuations
- White backlight allows the user to read the displayed data in a dark environment
- Features Bluetooth communication. Using the UNI-T smart measurement app, test results can be recorded and reported, and a data chart can be generated
- Ergonomic design for one-handed operation
- CAT III 600V
- drop protection: 2 m
Technical specifications:
- AC measurement range: 60 mV / 60 V / 600 V ±(1%+30)
- AC current measurement ranges: 6 A / 10 A ±(1.5%+30)
- DC voltage measurement ranges (direct current): 600 mV / 6 V / 60 V / 600 V ± 0.3% of reading DC current measurement ranges (direct current): 6 A / 10 A ±(0.5%+10)
- Auto-V range: 600 V ±(1%+3)
- LPF (ACV): 600 V ±(2%+3)
- Frequency measurement range: 99 Hz / 999 Hz / 999 Hz / Hz / Hz. ±(0.01%+3)
- resistance measurement ranges: 600 Ω to 6 MΩ ±(0.5%+5) / 40 MΩ ±(3%+5)
- Capacitance measurement range: 1000 nF / 10 μF / 100 μF / +0 μF / +0.10000 μF ±(2.5%+5)
- LCD display with a maximum reading of 60,000
- Relative measurement mode
- High voltage warning
- Audible and visual indication
- Low battery indicator
- Auto-off: approx. 15 minutes
- LCD backlight: automatic switch-off after 5 minutes
- Power supply: 3 x R03 (AAA) 1.5V batteries
- Weight: 346 g
- dimensions: 169 mm x 84 mm x 48.8 mm
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty.
UT219PV Professional AC/DC clamp meter specially designed for high-voltage photovoltaic environments. It offers exceptional accuracy and performance with a wide range of features. With automatic range selection and a clear display capable of showing up to 9999 digits, this clamp multimeter enables precise measurements of AC/DC voltage, current, low-frequency filtered voltage/current, inrush current, peak current, DC power, resistance, circuit continuity, diodes, capacitance and temperature. Its versatility extends beyond photovoltaic applications, as it can also be used in other high-voltage devices, such as energy storage systems, uninterruptible power supplies (UPS) and large motors. DC
- Current measurement: AC / DC 1000A
- DC power supply: 2500 kVA
- External clamp sensor: UT-CS09D (AC 3000 A)
- Solar panel polarity indication: when <-10 DCV, audible and visual alarm
- AC/LP pass filter
- Bluetooth-F pass filter
voltage/current.
- Measurement of alternating start-up current and peak value
- Automatic backlight and auto-off
- Certificates: CE (EMC, LVD), cETLus, RoHS
- Safety category: CAT III 1500V / CAT IV 600V
- Protection rating: IP6/Technical
Parameters:
- AC current (A): 999.9 A 40Hz–100Hz ±(2.0%+5), 100Hz–1000Hz ±(2.5%+5)
- DC current (A): 999.9 A ±(2.0%+5):/AC voltage (2.0%>-5)
- DC voltage (V): 999.9 V / 2500 V ±(1.0%+5)
- DC voltage (mV): 999.9 mV ±(1.0%+5)
V (with L.0%+5)
- AC voltage ±(2.0%+9)
- AC current (with LPF): 999.9 A ±(2.5%+9)
- Flexible clamp AC current sensor (with LPF): 30.00 A / 300.0 A / 3000 A ±(4.0%+9)
- 0.00 A / 300.0 A / 3000 A ±(4.0%+9)
-3p. 300.0 A / 3000 A ±(3.0%+5)
- DC power: 999.9 kVA / 2500 kVA ±(1.0%+5)
- Frequency: 50 Hz – 999.9 kHz ±(0.5%+5)
- Resistance (0.5%+5)
-999 Ω. 99.99 kΩ ±(1.0%+3)
- Capacitance: 100.0 μF / 1000 μF ±(1.0%+5)
- temperature: -40°C – 4000°C ±(1.0%+30)
- True RMS
- max. display: 9999
- LCD display: dual display (V+A)
- Jaws (max. conductor diameter) 35 mm
- Diode test
- Solar panel polarity indication: at <-10 V DC, audible and visual alarm
- high voltage alarm
- HOLD range exceeded indicator
-/AUTO
- current
- PEAK
- Bluetooth BT 5.0 app
- automatic backlight
- low battery indicator √
- flexible clamp compatible with UT-CS09D (optional)
- protection rating: IP65
- Power supply: 1.5V AA battery × 5 mm × 5 mm × 2 mm
Accessories:
- test probe
- temperature probe
- battery
manufactured by UNI-TREND
10 - 20 days
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty. A miniature digital multimeter with an attractive and practical design, the UT118C Pen-type is a lightweight and durable instrument featuring a True RMS measurement function, ensuring accurate readings. With the ability to measure voltages up to 600V AC/DC, a wide range of resistance and capacitance measurements, and gold-plated test leads with special tips for versatility and safe operation (CAT III 600V and CAT IV 300V), it is an excellent and cost-effective choice for DIY appliance repairers. It indicates live wires, ensuring greater safety when inspecting electrical equipment.
Product specifications:
- True RMS
- 6000-count display
- CAT III 600V/CAT IV 300V
- Voltage measurement 600 V DC/AC
High resistance measurement capacity > 600 V DC/AC
600 V
measurement: 60mF
- two-stage tip length adjustment
- gold-plated test leads with special tips, hardened phosphor bronze
- certification: CE (EMC, LVD), ROHS
Technical parameters:
- AC voltage (V60): V60/V/60 ±(1%+3)
- DC voltage (V): 6 V / 60 V / 600 V ±(1%+4)
- Resistance (Ω):
600 Ω / 6 kΩ / 60 kΩ / / 600 kΩ ±(1%+3)
600 Ω / 6 kΩ / 600 kΩ ±(1%+3)
+5 MΩ/600 kΩ ±(1%+3)
6 MΩ ±(2.5%+5)
- capacitance:
600.0 nF / 6 μF / 60 μF / 600 μF ±(3.5%+8)
6 mF ±(5.0%+9)
60 mF ±(10.0%+9) frequency:+9) 999.9 Hz / 9.999 kHz / 99.99 kHz / 999.9 kHz ±(0.01%+5)
- max. display: 6000
- Alternating: 0.1% to 99.9%
- NCV / LIVE test
- True RMS
- Diode test
- Resistance test
- Auto range
- 36 x 15 mm HTN LCD display / Dual-colour source indicator
AAA-1. package)
- Product dimensions: 182.5 mm x 38.0 mm x 38.5 mm
- Product colour: grey + red
Manufacturer: UNI-TREND
In stock
Contact us at contact@solartech.eu for more info regarding the inventory of this product.
This product comes with a 3-year warranty.
The UT673PV MPPT solar meter can effectively identify any faults in solar panels by testing their peak power, peak voltage, peak current, open-circuit voltage and short-circuit current. Thanks to its large display and automatic measurement capability, this device conveniently displays all measurement results simultaneously. Its lightweight design allows for easy portability, which greatly enhances operational and maintenance efficiency. Applications: solar panel manufacturers, solar panel users, assembly companies, etc.
Product parameters:
- for the installation and maintenance of solar panels
- the large LCD display shows all basic test values
- no batteries required, powered by the solar panel
- portable and convenient
- easy to use
- MC test
- Easy-to-use cable
Technical parameters:
- maximum power test (Pmax) 5 W to 800 W ±(1.0% + 10)
- peak supply voltage (Vmp) 12 V to 60 V ±(1.5% + 5)
- Peak current at 1.5% (Imp) - A ± (1.0% + 5). 5)
- open-circuit voltage (Voc) 12 V to 60 V ±(1.5% + 5)
- Short-circuit current (Isc) 0 A to 35 A ±(1.5% + 5)
- LCD display (52 x 66 mm)
- Overvoltage connection protection/overvoltage protection/reverse polarity protection
protection
- Overheating protection
- Overvoltage protection
- Manual MPPT test
- Data logger
- power: no batteries required, power from solar panel
- dimensions: 143 × 74 × 25 mm
- colour: red + black
- Category: CAT, CE certification<br, c/6-0V RoHS
Manufacturer: UNI-TREND
