{"product_id":"uni-t-ut622c-multimeter","title":"UNI-T UT622C multimeter","description":"\u003cp\u003eThe UT622C LRC device is a portable component tester — coils (inductance), resistors (resistance) and capacitors (capacitance) — and their secondary properties: D (loss factor), Q (quality factor), Θ (phase angle in degrees), Θ (phase angle in radians) and ESR (equivalent series resistance or parallel resistance). Component parameters are measured using alternating voltage with a selectable frequency of 100, 120, 1000, 10000 Hz, 100 kHz and a selectable amplitude of 0.1 Vrms, 0.3 Vrms, 1.0 Vrms at a signal source output impedance of 100Ω. The highest measurement accuracy is 0.1%.\u003cbr\u003e\nThe device features an intuitive 2.8-inch TFT LCD display with ten-level adjustable backlight brightness, a built-in high-capacity 1800mAh Li-Pol battery and a miniUSB connector for charging and data transfer to a computer. The maximum display value when measuring primary parameters is 99999, and the minimum value when measuring secondary parameters is 0.0001. Measurement mode – a measurement triggered by the TRI button or a command from a PC; or continuous measurement with adjustable test trigger rates of 20x\/sec, 5x\/sec, 2x\/sec. 2+1 or 4+1 terminal configuration (with UTR-L100k-H test cables included with this device).\u003cbr\u003e\nThanks to its technological sophistication, the device is also suitable for professional use – when connected to a computer (PC), it creates a component sorting station based on specified tolerance parameters and can be used in production lines, laboratories, etc. Intuitive TFT LCD display, 10 brightness levels\u003cbr\u003e\n- display range up to 99,999\u003cbr\u003e\n- maximum accuracy 0.1%\u003cbr\u003e\n- Ability to select components according to specified tolerance\u003cbr\u003e\n- AC voltage measurement: 100, 120, 1000 Hz \/ 0–1000 Hz amplitude measurement. Voltage: 0.1 Vrms, 0.3 Vrms, 1.0 Vrms\u003cbr\u003e\n- selection of equivalent mode (for Z \u0026lt;100Ω in series, for Z \u0026gt;10kΩ in parallel)\u003cbr\u003e\n- automatic component identification\u003cbr\u003e\n- built-in high-capacity Li-Pol battery: 3.7V\/1800 mAh: DC +5V charging power supply\u003cbr\u003e\n±0.25V, \u0026gt;1A\u003cbr\u003e\n- operating time on a single battery charge: typically 8 hours\u003cbr\u003e\n- Functions in data logging and statistics mode: AVG, MAX, MIN\u003cbr\u003e\n- Audible tone when buttons are pressed: yes, can be disabled\/enabled\u003cbr\u003e\n- button lock option: yes\u003cbr\u003e\n1, 6, automatic after shutdown minutes, or off\u003cbr\u003e\n- Data interface: mini USB\u003cbr\u003e\n- Data transfer rate to PC: 9600\/19200\/38400 baud\u003cbr\u003e\n- Audible and visual alarm for tolerance comparison results: off, pass, fail\u003cbr\u003e\n- Audible alarm selection: short beep, long beep, two short beeps\u003cbr\u003e\nin case of open circuit or short circuit reset\u003cbr\u003e\n: yes\u003cbr\u003e\n- Setting of tolerance value from nominal: 1% to 20%, default 5%\u003cbr\u003e\n- Component counting: all, compliant, non-compliant\u003c\/p\u003e\n\u003cp\u003eTechnical parameters:\u003c\/p\u003e\n\u003cp\u003e- Measurement range for primary impedance parameters:\u003cbr\u003e\ntype \/\/ minimum resolution within the display range 0.001 μH to 9999.9 H \/\/ 1 \/ 0.1 \/ 0.01 \/ 0.001 μH\u003cbr\u003e\ncapacitance C \/\/ 0.001 pF to 99.999 mF \/\/ 1 \/ 0.1 \/ 0.01 \/ 0.001 \/ 0.001 pF at 0.001 pF resistance \/\/\/\u0026gt;0.0 R\u003cbr\u003e0.0. 99.999 MΩ \/\/ 0.0001 Ω\u003cbr\u003e\nTotal impedance Z \/\/ 0.0001 Ω to 99.999 MΩ \/\/ 0.0001 Ω\u003c\/p\u003e\n\u003cp\u003e- Measurement range of secondary impedance parameters:\u003cbr\u003e\ntype \/\/ minimum resolution \/\/ 0.000 display range \/\/\/\/0000 display range 9.9999 \/\/ 0.0001\u003cbr\u003e\nQuality factor Q \/\/ 0.0001 to 99999 \/\/ 0.0001\u003cbr\u003e\nphase angle in degrees Θ degrees \/\/ -179.9° to 179.99° \/\/ 0.01°\u003cbr\u003e\nphase angle in rad \/ 2 radians -Θ. 3.1416 rad \/\/ 0.001 rad\u003cbr\u003e\nEquivalent resistance ESR \/\/ 0.01 mΩ to 999.99 Ω \/\/ 0.01 mΩ\u003c\/p\u003e\n\u003cp\u003e- display: backlit TFT LCD display with a diagonal of 2.8\" and a resolution of 320 x 240 pixels\u003cbr\u003e\n-9999999 pixels. Accuracy: best 0.1%\u003cbr\u003e\n- Component selection based on set tolerance: yes\u003cbr\u003e\n- voltage measurement: AC 100, 120, 1000, 10000 Hz or 100 kHz\u003cbr\u003e\n- Voltage amplitude measurement: 0.1 Vrms, Vrms, 0.1 Vrms, data transfer 0.1 Vrms, 0. Yes, after installing the software on a PC\u003cbr\u003e\n- power supply: 1800mAh Li-Pol battery and\/or 5V ±0.25V DC adapter, \u0026gt;1A\u003cbr\u003e\n- automatic charging management: even when the device is switched off\u003cbr\u003e\n- Charging and data interface: mini USB\u003cbr\u003e\n- Operating environment: temperature 5 to 35°C, humidity ≤ 35% - Weight with\/without battery: 305g \/ 420g\u003cbr\u003e\n- Product dimensions (H x W x D): 192 x 93 x 44 mm\u003cbr\u003e\n- Package dimensions: 225 x 220 x 63 mm\u003cbr\u003e\n- Safety and EMC certification: IEC\/EN 61010-1: 2010, EN 2013206, EN 61326-2-2: 2013\u003c\/p\u003e\n\u003cp\u003eContents of individual package:\u003c\/p\u003e\n\u003cp\u003e- UT622C device: 1 pc UTR-001 box: 1 pc\u003cbr\u003e\n- user manual: 1 pc\u003c\/p\u003e\n\u003cp\u003ePackaging for bulk customers:\u003c\/p\u003e\n\u003cp\u003e- standard quantity per box: 10 pcs\u003cbr\u003e\n- standard box dimensions: 370 x 305 x 475 mm\u003cbr\u003e\n- gross weight of 2 cartons: 2 kg\u003c\/p\u003e\n\u003cp\u003eMANUFACTURER: UNI-TREND\u003c\/p\u003e","brand":"UNI-T","offers":[{"title":"Default Title","offer_id":57062172000587,"sku":"07720300","price":293.05,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1021\/3323\/6043\/files\/07720300.jpg?v=1776539739","url":"https:\/\/solartech.eu\/products\/uni-t-ut622c-multimeter","provider":"SolarTech - Solar Inverters, PV Modules, Solar Accessories, ESS Battery","version":"1.0","type":"link"}